Parts Needed to Install Brake Controller on 2012 Chrysler Town and Country
Question:
Im looking to add trailer wiring to my 2012 Chrysler Town and Country. I will need electric braking capabilities, so have decided to use part #22121. Will the Draw-Tite I-Command Trailer Brake Controller part #5535 work with this wiring harness? Is there anything else Id need to buy to get the wiring/lighting/braking working?
asked by: Brian
Expert Reply:
The Tekonsha OEM Vehicle Wiring Harness # 22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller.
The included brake controller harness is compatible with and will plug into the Brake EVN # TK63VR that you also mentioned. The other end of the brake controller harness will need to be hardwired to your Town and Country. I have attached the complete installation instructions on this kit that you can check out as well.
You should not need any other wiring components to power both the lights and electric brakes on your trailer.
Products Referenced in This Question
Tekonsha BRAKE-EVN Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Automatic Leveling
- Under-Dash Box
- Up to 4 Axles
- LED Display
- Up to 90 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Shop: Trailer Wiring
- Search Results: trailer brake controller
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Trailer Hitch
- Shop: Redarc Tow-Pro Elite Brake Controller - Dash Knob - 2 Braking Modes - 1 to 3 Axles - Proportional
- Shop: Adapter 4-Pole to 7-Pole and 4-Pole
- Shop: Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers
- Search Results: brake controler
- Search Results: tekonsha brake controller
- Video: Bright Way Trailer Breakaway Kit with Switch Review
- Video: Review of Bright Way Trailer Breakaway Kit - Kit with Charger - 3802308
- Shop: 3" Wide Continuous Hinge - 6' Long - Steel
- Shop: Bright Way Push-to-Test Trailer Breakaway Kit with 1-Amp Charger and 5 Ah Battery - Top Load
- Shop: Rubber Bumper for Enclosed Trailer Ramp Door - 2-1/2" Diameter
- Shop: RV Camera
- Shop: Suspension Enhancement
- Search Results: etbc7
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Replacement Parts for Suburban Model SW6 DE Water Heater
- Q&A: Adding a 7-Way Trailer Connector to a 2010 Ford F-150 with Factory 4-Way
- Video: Review of Hopkins Wiring - Wiring Adapters - 37185
- Search Results: 90195
- Search Results: tk5906
- Search Results: brake controller
- Q&A: Brake Controller Recommendation for a 2003 Ford Ranger
- Video: Trailer Wiring Harness Adapter Installation - 2006 Ford Ranger
- Video: Trailer Brake Controller Plug-In Harness Replacement Installation - 2015 Toyota Sienna
- Video: Reese Custom Fit Vehicle Wiring - Trailer Hitch Wiring - 74682 Review
- Video: Draw-Tite Electric Trailer Brake Controller Wiring Kit Review
Mary
8/2/2020
I have a 2012 Town and Country, I already have a tow bar and will be ordering a ball hitch from etrailers. I really appreciate the tutorials and access to expert advice! I have no wiring for towing or brake controller installed. If I buy this 7 pin kit, do I have to have a 4 pin wiring already, or install one and then convert? Is there just a kit that I can install to pull my pop up camper without installing a 4 pin first?