Bolt Thread Length of Replacement Hub Assembly for Demco Kar Kaddy

Question

Question:

What size thread are the studs? Im guessing one of the three common sizes 7/16inch X 20 1/2inch X 20 9/16inch X 18

asked by: EC

1

Helpful Expert Reply:

You guessed right, because the Replacement Hub Assembly for Demco Kar Kaddy, Tow IT II, or Penske Tow Dolly # DM04369 uses 7/16” - 20 bolts.

I've added a link to a video review of this hub assembly for you to check out as well.

expert reply by: Kyle S

1

Answer 1

I went out to the warehouse and measured the Replacement Hub Assembly for Demco Kar Kaddy, Tow IT II, or Penske Tow Dolly #DM04369 from the gold piece rearward, and it measured 4-1/4" long.

view full answer...

Answer 2

You will be able to use hub bolts to mount the Aluminum Sendel Series T07 Black Machined Trailer Wheel #AM25DR. In order to make this work, you will need to use bolts that have a 60 degree cone and match the 1/2"-20 wheel bolt size used by these…

view full answer...

Answer 3

The Replacement Hub Assembly for Demco Kar Kaddy #DM04369 is the only hub assembly we have for the Kar Kaddy's. There is no 5 on 4 bolt pattern, you likely already have a 5 on 4-1/2 bolt pattern. I recommend double checking the measurements. I…

view full answer...

Answer 4

The Demco Kar Kaddy SS Tow Dolly with Disc Brakes part #DM9713045 uses disc brakes. The design is very similar to that of a modern day automobile. The wheel and hub/rotor are separate components. I have attached a diagram below. The recommended…

view full answer...

Answer 5

Thanks for reaching out! The replacement brake pads for your Demco Kar Kaddy SS #DM9713045 can be found as part #DM59VR on our site. This includes parts for both sides of the tow dolly. If you want to replace the whole assembly then you can do so by…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...