What Is The Depth Of The Replacement Hub Assembly For Demco Kar Kaddy Tow Dolly

Question

Question:

I was wondering if I could get the dimension from the mount flange rearward including the rear gold dust cap? I am trying to use this in a project. Thank you.

asked by: Brandon Z

0

Expert Reply:

I went out to the warehouse and measured the Replacement Hub Assembly for Demco Kar Kaddy, Tow IT II, or Penske Tow Dolly # DM04369 from the gold piece rearward, and it measured 4-1/4" long.

expert reply by: Bryce D

0

Depth Of The Replacement Hub Assembly
(click to enlarge)

Answer 1

The bolt pattern of the Replacement Hub Assembly for Demco Kar Kaddy, Tow IT II, or Penske Tow Dolly #DM04369 is definitely 5 on 4-1/2 inch which is the same as 5 on 115 mm. This hub definitely fits the Demco Kar Kaddy chrome replacement wheel…

view full answer...

Answer 2

Rather than installing hydraulic drum brakes you should look at a Kodiak Disc Brake Kit #K2R35D for your tow dolly. That is the style the new Demco Kar Kaddy X Tow Dolly #DM9713093 uses as it would make for a much better setup that will be easier…

view full answer...

Answer 3

You guessed right, because the Replacement Hub Assembly for Demco Kar Kaddy, Tow IT II, or Penske Tow Dolly #DM04369 uses 7/16” - 20 bolts. I've added a link to a video review of this hub assembly for you to check out as well.

view full answer...

Answer 4

Thanks for reaching out! The replacement brake pads for your Demco Kar Kaddy SS #DM9713045 can be found as part #DM59VR on our site. This includes parts for both sides of the tow dolly. If you want to replace the whole assembly then you can do so…

view full answer...

Answer 5

I have brake mounting flanges that will work for you. We have several different types and sizes so you will need to find the right size and then have it welded on by a licensed professional welder. For example, for a 2-3/8 inch round axle we carry…

view full answer...

Answer 6

It might be possible to add trailer brakes to your tow dolly but due to the age of it I can't give you the exact parts you'd need. You'd have to take your wheels and hubs off to check out and measure the spindle to determine…

view full answer...

Answer 7

The brake rotor designed to fit on the #DM04369 is the Replacement 10" Brake Rotor for Demco Tow Dollies - Qty 1 #DM03927-92. I've also listed the other replacement brake parts that are available for the Demco Kar Kaddy tow dolly below. -…

view full answer...

Answer 8

The Replacement Hub Assembly for Demco Kar Kaddy #DM04369 is the only hub assembly we have for the Kar Kaddy's. There is no 5 on 4 bolt pattern, you likely already have a 5 on 4-1/2 bolt pattern. I recommend double checking the measurements. I…

view full answer...

Answer 9

The Kodiak Disc Brake Kit part #K2R35D comes with rotors which measure 10-7/8" diameter but are commonly just referred to as 10" diameter rotors.

view full answer...

Answer 10

Welding a mounting flange, possible item #4-35, is a very precise installation. The flanges need to be installed square and concentric to the hub and drum assembly and each other. If the flange is installed incorrectly rapid brake lining wear,…

view full answer...

Answer 11

Since you have a boat trailer I recommend sticking with hydraulic brakes. This will not only be the easiest for you in order to make replacements but hydraulic brakes are the best for boat trailers because electricity and water don't mix…

view full answer...

Answer 12

There is a special jig required to weld on brake mounting flanges such as #4-35. The flange needs to be welded on concentric and square. Square meaning the flange must be a true 90 degrees from the spindle and concentric meaning the gap around the…

view full answer...