Trailer Hitch Recommendation for 2018 Audi Q7

Question

Question:

What trailer hitch would you recommend for 2018 Audi Q7?

asked by: Shawn

0

Expert Reply:

For your 2018 Audi Q7 the best trailer hitch we offer that I would recommend for you is the etrailer part # e88KR because it has a concealed cross tube which makes it less visible than other hitches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

We have 2 inch hitches that fit your 2021 Audi Q7 like the Curt #C13277 that you referenced but due to how the vehicle is designed there isn't a way to install a hitch on the vehicle without trimming the fascia. This Curt hitch would be the best…

view full answer...

Answer 2

While there are no major modifications or drilling required you will need to trim a small portion of the rear bumper fascia on your 2022 Audi Q7, for the Curt Trailer Hitch Receiver #C13277 to fit. I have a included an image that shows where the…

view full answer...

Answer 3

It sounds like you're looking for a trailer wiring harness for your 2017 Audi Q7. If the Audi came with the factory tow package but doesn't have the connector you can use the Curt #C55774 which will provide you with a 4-way and 7-way…

view full answer...

Answer 4

We do sell some wiring harness options for your 2019 Audi Q7 and we can get you to a 7-Way round style that works with your RV plug. To start off we have the #C59236 which splices into your OEM wiring or the ZCI Wiring #119250KIT which clamps around…

view full answer...

Answer 5

For your 2017 Audi Q7, if you don't already have a hitch I recommend the etrailer Trailer Hitch Receiver - Custom Fit - Class III - 2" #e88KR. This hitch receiver is a matte black powder coat finish over and e-base coat for excellent rust…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 11

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 12

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...