How To Re-Assemble the Titan Trailer Coupler # T4845000

Question

Question:

nuts and guts fell out of trailer coupler. do you have a diagram to put back together?

asked by: Tim

0

Expert Reply:

I pulled the Titan Trailer Coupler #T4845000 and the repair kit from our warehouse. I produced a short video for you showing how to reassemble the Titan # T4845000.

Also linked is an FAQ on trailer couplers.

expert reply by: Reno H

0

Answer 1

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 2

Your surge coupler will have either a sticker or an engraving on it, typically near where the coupler is located. If you can get me that information and what you're needing to replace on it I'd be more than happy to help you find what…

view full answer...

Answer 3

Thanks for the photos. It is clear you have a Titan brake actuator like the Brake Actuator with Manual Lockout - Bolt On - Drum - 2" Ball - 7,500 lbs #T63FR. It sounds like you need the Replacement Master Cylinder Assembly for Titan/UFP Brake…

view full answer...

Answer 4

In order to swap your surge brakes to electric over hydraulic, you're going to need to change out your actuator and add a proper brake controller. For an actuator I'd recommend going with the Hydrastar Electric Over Hydraulic Actuator for…

view full answer...

Answer 5

The coupler I recommend for your boat trailer is the Demco Channel Tongue Trailer Coupler #12564, which fits a 3" wide channel tongue, has a 10,000 lb capacity and uses the eZ-Latch system to fit a 2" hitch ball. This will allow you to hook…

view full answer...

Answer 6

There are several different surge brake options but I would need to know a bit more of what you have exactly to give you the best replacement option. First do you have Disc or Drum trailer brakes. Next I need to know the maximum weight your trailer…

view full answer...

Answer 7

Hey Scott, the bolt holes of the Dexter DX7.5L A-60 Brake Actuator w/ Electric Lockout - Disc #DX56FR are 3" apart horizontally and 2-1/2" apart vertically. The holes are 5/8" from the top and bottom of the actuator.

view full answer...

Answer 8

We do have Dexter brand master cylinder replacements for the model #UFP 60/A-75 brake actuators. I have listed both options below depending on what type of brakes you have: Drum Brakes - Replacement Master Cylinder Assembly for Dexter Brake Actuators…

view full answer...

Answer 9

First, release the mechanism that holds the coupler onto the ball. It may be a lever or a knob that has to be turned. Some require a dual action move where you would push back or forward on the lever while lifting up on it. If you have done this and…

view full answer...

Answer 10

The Titan Zinc-Plated, Leverlock Coupler #T4845000 that you referenced is designed to fit on a trailer tongue that measures 3 inches wide. If you measure the width of the insert portion of your surge coupler and it's 3 inches wide this will…

view full answer...

Answer 11

You can get the Titan Zinc-Plated, Leverlock Coupler #T4845000 to fit your 2-1/2 inch x 2-1/2 inch square tube, although there is not an adapter sleeve. Instead, you will need to have spacers welded onto the tongue in order to use this coupler. This…

view full answer...

Answer 12

Channel Tongue Trailer Coupler #CT-3001-Z requires a 2 inch wide tongue but I recommend a boxed tongue and not C-channel so there is more support where it counts. Steel tubing at least 1/8 of an inch of wall thickness will do the trick. The length…

view full answer...

How To Re-Assemble the Titan Trailer Coupler # T4845000

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching