Recommended Coupler for Boat Trailer With 3" Wide Channel

Question

Question:

I am looking for a new coupler for my trailer. I switching from surge to electric brakes so I just needs a standard coupler. The channel is 3in wide and the trailer with boat weights around 5400lbs

asked by: Matt B

0

Expert Reply:

The coupler I recommend for your boat trailer is the Demco Channel Tongue Trailer Coupler # 12564, which fits a 3" wide channel tongue, has a 10,000 lb capacity and uses the eZ-Latch system to fit a 2" hitch ball. This will allow you to hook up the latch simply by dropping the coupler over the hitch ball.

I've added a link to a video review of this coupler for you to check out.

expert reply by: Kyle S

0

Answer 1

The only difference between the Demco Channel Tongue Trailer Coupler part #12564 and Demco Channel Tongue Trailer Coupler part #DM12717 is the bolt pattern which is just slightly different with one having an extra hole.

view full answer...

Answer 2

I'm guessing it is approximately 3-3/8" across if you measured it. Unfortunately there are no options that will slide in because it won't line up correctly, and everything is designed to fit a 3" tongue so it is too…

view full answer...

Answer 3

You can lock out your surge brake actuator although it's not always the prettiest of solutions. You need to either weld the pieces together or drill holes through it putting in bolts to keep it from moving. It'll work but it completely…

view full answer...

Answer 4

While we don't have replacement parts for a Model LP70 actuator, we do have a great replacement solutions for it. Like the 70LP, these actuators are a fit for a 2" hitch ball, but they just have a slightly larger capacity at 7,500 lbs. You…

view full answer...

Answer 5

As shown in the provided photo, the approximate distance from the centerline of the trailer ball to the end of the coupler is 12 inches. The Demco #12564 accepts a 2 inch trailer ball.

view full answer...

Answer 6

The HydraStar Marine Electric Over Hydraulic Actuator w/ Breakaway and 7-Way RV Harness #HS381-9067 is designed to work with an aftermarket electric over hydraulic brake controller. This kit will require you to wire in the components using the wire…

view full answer...

Answer 7

I spoke with my contact over at Demco about coupler #12564. From the top (outside) of the coupler above the mounting holes down to the center of the mounting holes measures 1.029". What brand is the coupler you have now because the 1 inch…

view full answer...

Answer 8

Your question came in blank, but judging by the pictures you submitted it looks like your hub seal is bad and you are looking to replace what you have. To pick out the correct replacement seal you will need to use your digital dial calipers to…

view full answer...

Answer 9

In order to install the Demco Channel Tongue Trailer Coupler part #12564, you'll need to obtain three 1/2" Grade 8 Hex Bolts about 3-1/2" - 3-3/4" long with nuts from a local hardware store. The recommended torque for a bolt this…

view full answer...

Answer 10

Yes, the Demco Channel Tongue Trailer Coupler #12564 that you referenced does accept a 2-inch hitch ball and mounts to a 3-inch-wide trailer tongue. It's mounting hole spacing is indeed 3-inches and it offers a 10,000-lb weight capacity.…

view full answer...

Answer 11

The hole diameters for the Demco Channel Tongue Trailer Coupler item #12564 are 1/2 inch. It is recommended to use grade 8 hardware to attach the coupler to your trailer frame. You can find these bolts at a local hardware store as they do not come…

view full answer...

Answer 12

We do have an option for you, though the straight tongue trailer couplers that fit 3" tongues only fit either a 2" or 1-7/8" ball, but not both. If that's okay, the best option is a coupler from Demco: - Demco Channel Tongue…

view full answer...

Recommended Coupler for Boat Trailer With 3" Wide Channel

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching