Gooseneck Ball and Puck Trim Kit for Ford Factory Fifth Wheel Rail Kit

Question

Question:

Is there a puck or trim needed for the hole where the ball goes ? 2014 F 350 superduty. Purchased truck pre-owned no pucks or trim just holes. Ive attached pics. What all do I need for gooseneck set up ?

asked by: George

0

Expert Reply:

For a gooseneck ball to fit the factory rail kit of your 2014 Ford F-350 you'd want the Reese Elite kit part # RP30137 which would fit right into the pucks of your truck. We have the replacement puck trim kit part # RP58458 which will give you the trim rings you are needing.

expert reply by: Jameson C

0

click to enlarge

Answer 1

If you check out the picture I attached you'll see that the base of the B and W Companion Hitch part #BWRVK3300 basically matches the width of the pucks that are in the bed of your 2015 Ford F-350. If you used them as a template you could easily…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 9

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 10

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The centerline on the #BR27FR is going to be from the center of the hitch pin hole. If you draw a line straight out and measure the distance to the bottom of the hook that is 1". I have attached a diagram below for your reference.

view full answer...