What is the Inside Dimension of Hopkins 3/8 Inch Wire Loom and is it Split Down One Side

Question

Question:

2004 Excalibur trailer, 1 1/4 inch strandard hitch 1.Do you measure 1/2 inch and 3/8foot wire loom by the inside or outside diameter ? 2.Is the wire loom split on the side or do you have to thread the wire through it ? Thanks-

asked by: George W

0

Expert Reply:

I went out to the warehouse and pulled a Hopkins Wire Loom, # 39035, to take some measurements for you. The 3/8 inch diameter is the inside diameter of the loom. And it is already split the entire 10 foot length of the loom so you would not have to fish wires through it.

expert reply by: Michael H

0

Answer 1

The inside diameter of the Wire Loom, 3/8" Diameter #39035 is 3/8 inch and the outside diameter is 1/2 inch.

view full answer...

Answer 2

I would certainly recommend the 1/2-inch wire loom #459075-1. It will hold two jacketed 2 wire 10-gauge wire and three jacketed 2 wire 12-gauge wire. See pictures to the right. In addition, I was able to fit comfortably eleven individual 16-gauge…

view full answer...

Answer 3

3 gauge wire is about 0.229 inches in diameter, so Wire Loom 3/8" Diameter like #39035 will give it enough space for safety without further restricting the wire for heat dispersion. It will also avoid pinching or crimping the wire. You can use…

view full answer...

Answer 4

If you are wanting to secure the wiring on your trailer and keep it secure I recommend using a wiring junction box like part #38656 on your trailer. You can place the junction box on the tongue of your trailer and run the wires from the trailer into…

view full answer...

Answer 5

When people replace wiring that is run inside a channel or frame they will attach the new wiring to the end of the wire they want to replace and pull it carefully from the other end. If you are unable to pull the wire, you can use a fish wire to try…

view full answer...

Answer 6

I would go with a 3/8 inch diameter, like #39035. That should provide enough space for the wires and still give good coverage. This loom comes in a 10 foot length. If you needed less of expect that you might have other wiring to run with the existing…

view full answer...

Answer 7

I highly recommend the etrailer Trailer Hitch Receiver #e38KR for your 2024 Hyundai Tucson PHEV because it's the only trailer hitch option for your vehicle that comes with a matte black finish. This finish not only looks more OEM than the…

view full answer...

Answer 8

First of all you will need the Roadmaster Direct-Connect Base Plate Kit 524470-5 #RM97RR for your 2024 Ford Maverick. The item #RM39FR you found is Roadmaster part number 524465-5 which fits certain Ford Escapes. Do understand the baseplate above…

view full answer...

Answer 9

Sure can, the correct trailer hitch and 4-way wiring harness for your 2024 Kia Sportage are the following: - etrailer Trailer Hitch Receiver #e38KR - T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector #C99DR I verified both fits…

view full answer...

Answer 10

Yes, the Curt Trailer Hitch Receiver part #C96NR is a confirmed fit for a 2023 Jeep Grand Cherokee. It's also a confirmed fit for a 2023 Jeep Grand Cherokee L not that it matters. It fits both the Grand Cherokee and Grand Cherokee L so there will…

view full answer...

Answer 11

There really isn't a difference between the two Curt hitches that fit your 2022 Jeep Grand Cherokee L or #C96NR and #C97JR. I would go with whichever is priced better. Now for trailer wiring I would go with the Tekonsha part #TK39VR as it has a…

view full answer...

Answer 12

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...