What is the Best Size Wire Loom for Bonded 4 Wire and One 12 Gauge Wire

Question

Question:

What size wire loom do I need to hold bonded 4 wire and 1 12ga?

asked by: Darrien A

0

Expert Reply:

I would go with a 3/8 inch diameter, like # 39035. That should provide enough space for the wires and still give good coverage. This loom comes in a 10 foot length. If you needed less of expect that you might have other wiring to run with the existing wires, you can go to a 1/2 inch loom, sold in 1 foot increments, # 459075-1.

expert reply by: Michael H

0

Answer 1

First of all you will need the Roadmaster Direct-Connect Base Plate Kit 524470-5 #RM97RR for your 2024 Ford Maverick. The item #RM39FR you found is Roadmaster part number 524465-5 which fits certain Ford Escapes. Do understand the baseplate above…

view full answer...

Answer 2

When installing the Roadmaster Brake-Lite Relay Kit for Towed Vehicles #RM-88400 in your 2018 Ford f-150 with neutral tow kit, you will want to use Instructions "B" for the installation. Roadmaster states that if you have a Ford…

view full answer...

Answer 3

The diode that you want for your charging line from your Motorhome to your towed vehicle (Toad) is the Roadmaster Single Park Light Diode #RM-690. This diode will allow up to 85 amps at 12V and will only allow power to flow in one direction to…

view full answer...

Answer 4

You can attach the Brophy Recessed Trailer D-Ring Tie Down with Backing Plate, #RR5K, most anywhere on a trailer. The recessed D-Ring is designed to be recessed in a wood surface (floor, wall) and using the steel backing plate will make a stronger…

view full answer...

Answer 5

If you have a flat tow wiring kit with diodes, then you need the Roadmaster #RM-88400 Brake Light Relay Kit. It is normal behavior for those lights not to work when the wiring kit is active. We want the towing vehicle (through the wiring kit) to…

view full answer...

Answer 6

Yes, since your braking system presses the brake pedal of your 2009 Ford Escape and the brake lights come one with the ignition off you need to use a brake lite relay part #RM-88400 so that the LED bulb and socket kit part #RM-152-LED turn signals…

view full answer...

Answer 7

Yes, The Roadmaster Brake-Lite Relay Kit for Towed Vehicles #RM-88400 will work with your wiring system to ensure that your towed vehicle's turn signal lights flash in tandem with your RV's lights. Using this relay will not interfere with…

view full answer...

Answer 8

Correct, you must turn on your motorhome's running lights/parking lights in order to get the Roadmaster Brake-Lite Relay Kit for Towed Vehicles #RM-88400 to work.

view full answer...

Answer 9

I went out to the warehouse to measure the square holes in the Trailer D-Ring Tie Down, #LRB1. According to my measurements it will accept bolts no larger than 7/16 inches in diameter. A 3/8 inch bolt would probably be the most ideal size to use.

view full answer...

Answer 10

The inner dimensions of the Commercial Grade Battery Box for Group 4D Batteries #329-HM408 are 21-3/16" long x 9-5/8" wide x 11-1/8" tall. Based on the dimensions of your LifePo4 batteries you'd easily be able to fit two in this…

view full answer...

Answer 11

In order to wire your cargo trailer for both 12 volt DC and 110 volt AC power you would need to install a AC/DC distribution panel and power converter which we currently do not offer. You would then wire the 12 volt power to the converter along with…

view full answer...

Answer 12

I would certainly recommend the 1/2-inch wire loom #459075-1. It will hold two jacketed 2 wire 10-gauge wire and three jacketed 2 wire 12-gauge wire. See pictures to the right. In addition, I was able to fit comfortably eleven individual 16-gauge…

view full answer...

What is the Best Size Wire Loom for Bonded 4 Wire and One 12 Gauge Wire

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching