Inside and Outside Diameter of Wire Loom, 3/8" Diameter # 39035

Question

Question:

Michael noted the ?inch wire loom is the inside measurement. What is the outside measurement? I need to be sure I can get it to fit where I need it to run or if I need to get the ¼inch loom and fight to get the wires in.

asked by: Tere

0

Expert Reply:

The inside diameter of the Wire Loom, 3/8" Diameter # 39035 is 3/8 inch and the outside diameter is 1/2 inch.

expert reply by: Jameson C

0

Answer 1

I went out to the warehouse and pulled a Hopkins Wire Loom, #39035, to take some measurements for you. The 3/8 inch diameter is the inside diameter of the loom. And it is already split the entire 10 foot length of the loom so you would not have to…

view full answer...

Answer 2

Yes, you can use Metal Loom Clamp - 1/2" #A0500 with Wire Loom 3/8" Diameter #39035. It will secure the loom to your frame but it will not clamp tightly around it. If you want a tight fit at the clamps you can use 3/4" x 60'…

view full answer...

Answer 3

I would certainly recommend the 1/2-inch wire loom #459075-1. It will hold two jacketed 2 wire 10-gauge wire and three jacketed 2 wire 12-gauge wire. See pictures to the right. In addition, I was able to fit comfortably eleven individual 16-gauge…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 12

Yes, it is! Honda and other manufacture's like to leave the fuses out of new vehicles that do not come with a functional towing package to save on costs. You can verify if you're missing the fuses by checking your fuse box but I am pretty…

view full answer...