Recommended Trailer Hitch and Wiring for 2014 Honda CR-V LX

Question

Question:

Its ok that I put a drawtite on my Honda CR-V LX as long as I stay in the cars 1599 lb towing weight? I like it and looks like easy install!!

asked by: Steve C

1

Helpful Expert Reply:

The Draw-Tite Class III Max Frame Round Tube Receiver Hitch # 75742 referenced in your question is confirmed to fit your 2014 Honda CR-V LX.

I did take a look at the online owner's manual for your Honda CR-V and saw that the maximum trailer weight is 1,500 pounds. As long as you stay below this weight, you can absolutely install this hitch and tow a lightweight trailer. You are correct that this is a pretty simple installation, as the custom hitch will use existing holes in the vehicle's frame to eliminate the need for any drilling. I have attached an installation video on your 2014 CR-V that you can use for reference, along with the written instructions. All of the necessary hardware is included.

In order to tow a trailer, you will also need a trailer wiring harness. For this I recommend the Tekonsha T-One # 118561. This custom harness will install by plugging into built-in ports located in the rear cargo area behind the driver and passenger side interior trim panels. This will provide you with a 4-Way connector that will connect with and power a trailer's basic signal lights.

I have again attached an installation video that you can check out.

Lastly, you will need a ball mount and hitch ball to pull the trailer. The Curt Ball Mount # D-4 might be a nice option. This will attach to your hitch and offer a rise of 3/4 inch or a drop of 2 inches. You will just add a compatible hitch ball like the 2 inch # 63845 or the 1-7/8 inch # 19260 and the Hitch Pin and Clip, # PC3. I have attached a great article that explains how to choose the best ball mount for your setup, along with a link that will take you to our available selection if this particular unit does not have the rise or drop you need.

I have also included a couple articles on trailer towing that you might find helpful.

expert reply by: Chris R

1

Answer 1

It does seem rather odd that Draw-Tite #75742 would construct the hitch with a mount to attach a trailer connector mounting bracket when the trailer connector harnesses for the vehicle are designed to be installed so that the trailer connector is…

view full answer...

Answer 2

With Draw-Tite trailer hitch #75742 installed on your 2014 Honda CR-V the face of the receiver will be almost flush with the rear bumper. It won't stick out quite as far. Take a look at the picture I have included. You can see that the…

view full answer...

Answer 3

The main reason you would use a class III hitch like the Draw-Tite Max-Frame Trailer Hitch Receiver #75742 you referenced is because, the 2" x 2" receiver opening featured on a class III hitch is the most common size for hitch…

view full answer...

Answer 4

The Draw-Tite trailer hitch receiver, part #75547, uses 4 hex bolts that are M10 X 1.25 X 30. However, you shouldn't tap the threads uness you absolutely have to as a last resort. I highly recommend cleaning them before tapping them.…

view full answer...

Answer 5

The install instructions use to say to measure 17 inches from the top corner to make the cut, but several customers have told us that it was a better fit to use 16-1/4 inches instead and now the install instructions have been changed. Aside from…

view full answer...

Answer 6

The bolts that come with the Draw-Tite #75742 for your 2014 Honda CR-V are 10mm bolts. These are the hex bolts M10X 1.25X 30. I went ahead and attached the diagram that shows these bolts in the instructions and where they install. They are item #1 in…

view full answer...

Answer 7

For your 2014 Honda CR-V we have two hitch sizes available. The smaller and very light duty 1-1/4 inch size and the much more popular and versatile 2 inch size which has higher towing capacities. I would say that you will want the 2 inch size as…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

Answer 11

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Recommended Trailer Hitch and Wiring for 2014 Honda CR-V LX

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching