Why Does Hitch for 2014 Honda CR-V Have Mount for Wiring When it Installs in the Cargo Area
Question:
I am installing a Draw-tite 75742 Class 3 hitch. The hitch comes with a moutning plate for the electrical connector. Your video shows the installation of a 118561 harness that sits inside the spare tire well. Why not use a harness that mounts on the hitch? Convenience? Operation quality? Looks? Is the 118561 the harness you would recommend? Thank you
asked by: Jeff K
Expert Reply:
It does seem rather odd that Draw-Tite # 75742 would construct the hitch with a mount to attach a trailer connector mounting bracket when the trailer connector harnesses for the vehicle are designed to be installed so that the trailer connector is stored in the vehicle when its not being used to protect it from damage and corrosion.
If you can locate a grommet in the floor of the cargo area that would allow you to pass the 4 pole connector outside the vehicle, you could certainly do so. There's usually a grommet in the lowest point of the spare tire well which should work well for that purpose. Make a cut in the grommet and feed the trailer connector through the hole, but be sure to seal up the hole afterword with some silicone RTV like # LT37467 to prevent exhaust fumes from getting in the vehicle. You'd use a mounting bracket like # 18144 attached to the mount on the hitch to hold the trailer connector.
For a trailer connector, the Tekonsha # 118561 would work great. You'll also need a ball mount like part # 27533 and # 19260 for a 1-7/8 or # 63845 for a 2 inch trailer ball.
I'll link to install videos for the Draw-Tite # 75742 Class III hitch and the trailer wiring harness.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Loctite RTV 598 High-Performance Silicone Gasket Maker - Black - 2.7-Fl Oz Tube
- Lubricants Sealants Adhesives
- Sealant
- Gasket Maker
- 2.7 oz
- Loctite
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 675 lbs TW
- 4500 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: Trailer Hitch Installation - 2016 Honda CR-V - Draw-Tite 75742
- Shop: Trailer Wiring
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Tekonsha Custom Fit Vehicle Wiring - Trailer Hitch Wiring - 118561 Review
- Q&A: What is the Size of the Bolts that Attach to My Frame from the Draw-Tite Hitch # 75742?
- Video: Trailer Wiring Harness Installation - 2016 Honda CR-V 118561
- Shop: Convert-a-Ball Cover for Interchangeable Shank
- Shop: Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
- Shop: Convert-A-Ball Interchangeable Ball Set - 3 Balls - 1" Shank - Stainless
- Shop: Draw-Tite QSP Trailer Hitch Silencer and Cover for 2" Hitch Receivers
- Video: etrailer.com Flush Design Trailer Hitch Receiver Lock Review
- Shop: Side Window Vents
- Q&A: Does Draw-Tite Trailer Hitch 75742 Stick Out Passed the Bumper on a 2014 Honda CR-V
- Q&A: Recommended Trailer Hitch and Wiring for 2014 Honda CR-V LX
- Q&A: Benefits Of Using A Class III Hitch For A 2014 Honda CR-V
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Video: Trailer Wiring Harness Installation - 2014 Honda CR-V 118561
- Q&A: How to Lower Muffler to Access Mounting Holes for Trailer Hitch Receiver on 2014 Honda CR-V
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Draw-Tite Ball Mounts - Fixed Ball Mount - 40332 Review
- Video: Review of etrailer Hitch Locks - Standard Hitch Pin - E98880
- Shop: Base Plate for Tow Bar
- Shop: Vehicle Tow Bar Wiring
- Article: What To Look For When Buying Ratchet Straps
- Q&A: What Size Bolts are Used to Install Draw-Tite # 75547 on a Honda CR-V
- Q&A: Cut Out Dimensions for Appearance Panel for Hitch Install on a 2015 Honda CR-V