Wheel Strap Recommendation for Securing 8,000 lb Ford Truck

Question

Question:

Im looking for product recommendations to secure a F250 to a flat bed trailer 14,000lb rated trailer. the truck weights aproxamitly 8,000lb. I would prefer straps over chains. I notice a lot of straps have a breaking strength of 10,000lb and a safe working load of 3,333lb. if I am using 4 straps, how do I determine the safe working load required? do I take my 8,000 and divide by 4? Are the 3,333lb straps sufficient? Or do I need to order something more heavy duty such as a chain? Thanks

asked by: Derek

0

Expert Reply:

You'd be fine using a strap rated for 3,333 lbs WLL for each wheel to secure your 8,000 lb truck.

We have the Erickson Adjustable Ratcheting Wheel Net w/ Hooks # EM58522 that is rated for 3,333 lbs WLL and 10k as break strength.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 3

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 4

You are correct that is a 3,500 lb axle. If you want a bearing kit the #BK2-100 you looked at is the right one. This comes with a #L44649 outer and #L68149 inner bearing along with a #58846 (10-19) grease seal. If you want a replacement idler hub you…

view full answer...

Answer 5

The etrailer E-Track Roller Idler #e67HR is 3" from the top of the e-track to the bottom of the roller.

view full answer...

Answer 6

It is not uncommon for certain factory brake controllers to have issues with electric over hydraulic brakes. This would be the first we have heard of this issue with a 2023 Ford F-350, but it is possible that the brake controller in your ford is…

view full answer...

Answer 7

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...

Answer 8

With plywood walls that are as thin as yours, it's possible that they may not support what you are looking to do. The only way you will be able to utilize the Erickson Horizontal E-Track #EM59150 (2 feet) or #E19148 (5 feet) is by installing it…

view full answer...

Answer 9

The Bulldog Winch Ratcheting Wheel Tie-Down Strap #BDW20362 is designed to connect to a D-Ring type of connection point so you wouldn't need to install an e-track on your trailer. For your application I recommend installing the Brophy D-Ring Tie…

view full answer...

Answer 10

The #168233 Double Lip Grease Seal has an outside diameter of 2.332 inches and an inside diameter of 1.688 inches. This seal is not compatible with a AF2527E seal with a O.D 2.312, because, even though the O.D. id very close, the inner diameter of…

view full answer...

Answer 11

Yes we do have backing plates for the e-tracks. I recommend going with etrailer E-Track Backing Plates w/ Hardware - Galvanized Steel - 6" Long x 6" Wide - Qty 4 #e66RR which is a nice kit that includes 4 plates and all the necessary…

view full answer...

Answer 12

E track like the part #E19148 (5 foot section) would work well for what you are looking to do. People use E track for car haulers all the time and it works well. We even have a wheel strap designed for E tracks, part #EM58523 which will work great.

view full answer...