Will Bulldog Powered Drive Kit Fit a Fulton 12K Magnum Jack

Question

Question:

Is this Bull Dog Powered Drive kit compatible with a Fulton Magnum Series Heavy Duty 12,000 Lb. Capacity Leg jack. Use is horse trailer with living quarters. Currently manual crank.

asked by: Teri

0

Expert Reply:

Bulldog Powered-Drive Kit # BD1824200100 comes with the parts needed to install and use the kit with your Fulton Magnum 12K jack as long as it was made after 2003. If it was made in 2003 or earlier then there isn't a kit for it.

expert reply by: Michael H

0

Answer 1

The Bulldog 10K/12K jacks with 2-speeds will have a gear box on them such as #BD183816 and so for it you would use powered drive kit #BD1824180100. The single speed jacks will not have a gear box like #BD182815 so you would use kit #BD1824200100.

view full answer...

Answer 2

The weight on a trailer near the front is going to be less than the gross weight of the trailer or the weight above the axle(s). It is possible that using one motor on the landing gear could lift the weight but the motors themselves have a specific…

view full answer...

Answer 3

I apologize for the confusion. It sounds like you have found some conflicting answers in the past, so I took the liberty to contact Bulldog directly and this is what they said: "The 12k RAM jack has a smaller diameter cross-shaft, therefore the…

view full answer...

Answer 4

I spoke with my contact at Bulldog. He stated that the optimum place for the powered drive motor, #BD1824200100, is on the street side (driver side) jack on the inside of the trailer. However, if you do not have the space to mount it like this then…

view full answer...

Answer 5

Yes, we have heard back from our customers that the Bulldog Powered-Drive Kit for Single-Speed Jacks part #BD1824200100 will also work on 12,000 lb RAM jacks like the Square Direct Weld Jack part #TJD-12000SP-R2. I would have to agree as well because…

view full answer...

Answer 6

The wiring for the Bulldog Powered-Drive Kit #BD1824200100 is as follows for the four wires in the wiring harness. The Black wire from the battery goes to the Black wire on the harness The Red wire from the battery goes to the Red wire on the harness…

view full answer...

Answer 7

I checked with Bulldog and here is why they include the extra gears with the #BD1824200100: If your date code is before E06 (May 2006), then you will also need to change out the bevel gear (included) to accommodate the larger dowel pin (included).…

view full answer...

Answer 8

I can tell you that the motor in Powered Drive Kit #BD1824200100 is a 12 volt motor that operates at 32 RPMs and 85 watts. I spoke with my contact at Bulldog and he said that the intermittent torque for the motor is 100 foot pounds. He also added…

view full answer...

Answer 9

The Bulldog Powered-Drive Kit part #BD1824180100 is for two speed jacks whereas the Bulldog Powered-Drive Kit part #BD1824200100 is for single speed jacks. However, we can only confirm that these work with Bulldog jacks that have a 12,000 lb support…

view full answer...

Answer 10

The Bulldog Powered Drive Kit for Single Speed Jacks #BD1824200100 has a 1-inch diameter shaft to transmit its power to your landing gear. The motor alone from this kit is available as part #BD1046130-00. A 1-inch cross shaft #BDCS730300 is also…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...