How Much Torque Does Motor Produce in Bulldog Powered Drive Kit for Single Speed 12K Jacks

Question

Question:

Looking at my bulldog pro series 12,000 lb jack it says it requires a minimun torque of 125 ft/lb to operate. Does this power drive unit have enough torque?

asked by: Stewart S

0

Expert Reply:

I can tell you that the motor in Powered Drive Kit # BD1824200100 is a 12 volt motor that operates at 32 RPMs and 85 watts. I spoke with my contact at Bulldog and he said that the intermittent torque for the motor is 100 foot pounds. He also added that this kit should only be used with a Bulldog set up and not a Pro Series jack.

If you can give me the model number of your jack I can determine if there are any other kits that will fit.

expert reply by: Michael H

0

Answer 1

Yes, in order to use the Square 2-Speed Jack w/ Crank part #TJD2SP-12000SP-F in tandem you would need to obtain the correct follow leg which is the Square Direct Weld Jack part #TJD-12000SP-F2. The handle for this follow leg can be discarded as you…

view full answer...

Answer 2

The Dexter Dual Trailer Wheel Lug Nut with Swivel-Flange part #6-118 will require a 32mm socket which is roughly the same size as a 1-1/4 socket.

view full answer...

Answer 3

We do have what you are looking for but it is our part number #6-190.

view full answer...

Answer 4

I checked with Bulldog and here is why they include the extra gears with the #BD1824200100: If your date code is before E06 (May 2006), then you will also need to change out the bevel gear (included) to accommodate the larger dowel pin (included).…

view full answer...

Answer 5

I apologize for the confusion. It sounds like you have found some conflicting answers in the past, so I took the liberty to contact Bulldog directly and this is what they said: "The 12k RAM jack has a smaller diameter cross-shaft, therefore the…

view full answer...

Answer 6

Bulldog Powered-Drive Kit #BD1824200100 comes with the parts needed to install and use the kit with your Fulton Magnum 12K jack as long as it was made after 2003. If it was made in 2003 or earlier then there isn't a kit for it.

view full answer...

Answer 7

The wiring for the Bulldog Powered-Drive Kit #BD1824200100 is as follows for the four wires in the wiring harness. The Black wire from the battery goes to the Black wire on the harness The Red wire from the battery goes to the Red wire on the harness…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

How Much Torque Does Motor Produce in Bulldog Powered Drive Kit for Single Speed 12K Jacks

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching