Shaft Diameter for Bulldog Powered Drive Kit for Single Speed Jacks BD1824200100

Question

Question:

What shaft size will this motor fit?

asked by: Kent

0

Expert Reply:

The Bulldog Powered Drive Kit for Single Speed Jacks # BD1824200100 has a 1-inch diameter shaft to transmit its power to your landing gear. The motor alone from this kit is available as part # BD1046130-00. A 1-inch cross shaft # BDCS730300 is also available.

expert reply by: Adam R

0

Answer 1

Send me the pictures you have and I'll see if it's something we can get.

view full answer...

Answer 2

Good news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears #TJD-12000-RODNUT in the #12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience. Basically,…

view full answer...

Answer 3

Unfortunately we do not offer a drill adapter for the square jack #TJD-12000SP-R2NH. The only way to raise and lower the jack will be with the manual crank handle #TJD-12000-HD. Bulldog used to make a powered drive kit that worked with these jacks,…

view full answer...

Answer 4

The only difference between the two landing gear sets you referenced is that Landing Gear #RVLG-8HDL comes with a handle and #RVLG-8000 does not. Apart from that they are the exact same landing gear sets, with 20-1/2" of travel, an 8,000 lb…

view full answer...

Answer 5

The handle that you need for the Square Direct Weld Jack - Drop Leg w/ Spring Return part #TJD-12000SP-R2NH is part #TJD-12000-HD. This handle replaces the handle on all of the TJD-12000 Series square jacks. It comes with the bolt and hardware needed…

view full answer...

Answer 6

To use the 25K etrailer Square Gooseneck Companion Jack #TJD-25100 at the front of your TopHat trailer you just need the following parts: - Connecting Rod #LG-XTB - Sidewind Crank #TJD-12000-HD We don't have a bracket for the connecting rod but…

view full answer...

Answer 7

Ultra-Fab T-Slot Power Drill Adapter #UF48-979071 is designed for use with Ultra-Fab scissor jack applications but is not confirmed to work with landing gear. You would have to go by the measurements. The inner diameter of the hole is 0.66 inches and…

view full answer...

Answer 8

I spoke with my contact at Ultra-Fab about the Power Twin II Electric Stabilizer, part #UF39-941705. They recommend not using this system because of the movement any livestock would make in the trailer. They said any movement would cause additional…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 12

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Shaft Diameter for Bulldog Powered Drive Kit for Single Speed Jacks BD1824200100

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching