Does Draw-Tite Trailer Hitch 24792 Come with Pull Wires to Install Bolts in Frame of 2007 Honda CR-V

Question

Question:

Does the draw Tite hitch #24792 come with the wires to pull the bolts back down through the holes in the frame

asked by: Tommy

1

Helpful Expert Reply:

I checked the parts breakdown in the instructions for Draw-Tite trailer hitch # 24792 and it does indicate that two 7/16 inch pull wires are included. I have linked those instructions and a video showing an example installation for you.

expert reply by: Michael H

1

Answer 1

If all you plan on towing is the boat and trailer then 200 pound tongue weight capacity and 2,000 pound gross trailer weight capacity of the Draw-Tite trailer hitch #24792 that you have referenced would be a good choice. Check the owners manual on…

view full answer...

Answer 2

There are both Class I and Class III trailer hitches available that are confirmed to fit your 2010 Honda CR-V. The available Class I hitches, such as the Draw-Tite Sport Frame #24792, feature a square tube design, while the Class III hitches like the…

view full answer...

Answer 3

I'd be happy to help! All of the hitches for your 2011 Honda CR-V weigh relatively the same when it comes to the different classes, and while the Class I hitches definitely weight lighter I recommend using a Class III hitch since they have a…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...