Recommendation for a 14,000 Pound Ball Mount for a 2011 Ford F-350 Dually

Question

Question:

I am looking for a ball mount set up for my 2011 F-350 DRW. 14k rating with a 2 rise and 2 5/16 ball. Do you have anything that will work? Thanks.

asked by: Rick S

0

Expert Reply:

The closest ball mount we have to a 2 inch rise that is also rated for 14K is the Cushioned Ball Mount, # AMSC2HD. It has a rise of 1-1/2 inches and accepts a ball with a 1-1/4 inch shank. For a ball, you can use # 63836.

Another option would be an adjustable ball mount, # C45900.

expert reply by: Michael H

0

Answer 1

The ball platform on the Convert-A-Ball Ball Mount for 2" Hitches part #AMSC2HD is slightly thicker than normal so you will want to use a hitch ball with an extended length shank. I recommend the 2" Hitch Ball part #A-90 or 2-5/16"…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 8

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 9

It is not uncommon for certain factory brake controllers to have issues with electric over hydraulic brakes. This would be the first we have heard of this issue with a 2023 Ford F-350, but it is possible that the brake controller in your ford is…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…

view full answer...

Answer 12

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...