Recommended Trailer Hitch and Wiring for 2005 Honda Accord

Question

Question:

Hi there! I am going to be pulling a small trailer that weighs about 1000 pounds. I was going to pull it with my 2013 Hyundai Elantra sedan, but since it is a 4cyl, I thought it might be a better idea to tow it with my 2005 Honda Accord which is a V6. Before I go buying the hitch and necessities to tow, I would like a second opinion. I understand they are both cars, but is would in fact, the V6 Honda Accord make it easier to tow because it has more power? Or is it safe to go with the Hyundai Elantra because it is a newer vehicle. Thanks so much!

asked by: Madison

0

Expert Reply:

I did some research on both your 2013 Hyundai Elantra Sedan and 2005 Honda Accord.

You are correct that towing with your older 2005 Accord will be the better option, primarily because of its V6 engine. According to the online owner's manual for your 2013 Hyundai Elantra, this vehicle is actually not designed to tow any size trailer and Hyundai does not recommend doing this. Your 2005 Accord, on the other hand, is able to tow a light trailer up to 1,000 pounds.

Since you will be very close to or at the absolute capacity on the Accord with your 1,000 pound trailer, I recommend doing everything you can to reduce some of its loaded weight by removing some cargo or accessories. I also recommend verifying the loaded weight of your trailer before going on a trip since it will be very close to exceeding the vehicle's capacity.

For your 2005 Honda Accord, I recommend the Draw-Tite Sportframe Trailer Hitch Receiver # 24787. This Class I trailer hitch is confirmed to fit this vehicle and will use existing holes in the vehicle frame to ease the installation process. Just note that on V6 models like yours, you will need to drill a small hole in the heat shield to properly attach the hitch. I have included the installation details for you to check out.

You will also need to install a 4-Way connector at the rear of the vehicle to connect with and power the trailer's signal lights. I recommend the Tekonsha T-One Vehicle Wiring Harness # 118302. This is a custom fit harness that will connect directly to built-in ports located inside the trunk behind the driver side tail light. I have attached an installation video on the 2006 Honda Accord that you can use for reference.

Lastly, you will need a ball mount. I recommend looking at the Draw-Tite Drawbar # 3592, which features a 2-1/8 inch rise or 2-3/4 inch drop. You will want to choose a ball mount that has sufficient rise or drop to tow your trailer level. If this unit does not have the needed rise or drop, I have attached an article that will help you in choosing the correct ball mount along with our available selection.

expert reply by: Chris R

0

Answer 1

I reached out to my contact at Curt Manufacturing and asked them if it would indeed be safe to use the hitch receiver as a mounting location for a floor jack and they stated that only on a Class III or above receiver would they recommend using the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 6

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 7

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 8

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 11

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

Answer 12

The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…

view full answer...