Is Drilling Required To Install Curt Trailer Hitch Receiver # 12051 On My 2011 Chevrolet Malibu LT

Question

Question:

I was wondering if there is any drilling required to installing the trailer hitch....code 12051 for a 2011 Cheverolet Malibu LT Thank you

asked by: Len

0

Expert Reply:

To install the Curt Trailer Hitch Receiver, part # 12051, on your 2011 Chevrolet Malibu LT you will need to drill 2 holes that are 17/32 of an inch. There is a template included with part # 12051 so that you drill in the correct spots. All of the hitches available for the 2011 Malibu require drilling to install.

A drawbar, pin and clip come included with part # 12051. To complete your towing setup, you may be interested in the following:
Wiring, part # 118450
1-7/8 Inch Hitch Ball, part # 19256
2 Inch Hitch Ball, part # 19258

I have linked instructions for the Curt Trailer Hitch Receiver, part # 12051, and an FAQ Article on tips when installing a trailer hitch.

expert reply by: Reno H

0

Answer 1

For a replacement tire for your DK2 utility trailer I recommend the Taskmaster 5.30R12 Radial Trailer Tire - Load Range C #TT53012C. This will be a direct replacement for your current tire which is also load range C with a maximum load of 1,050 lbs…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

The 8-14.5 tires are an older metric size no longer used today. Therefore, you would need to replace these along with the wheels in order to update them. In order to see if we have any options for you, we'd first need to determine the bolt…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...