Recommended Trailer Hitch for Toyota Highlander that Fits with Full Size Spare Tire

Question

Question:

My Highlander is full size spare tire. Can I install C13200?

asked by: GZC

0

Expert Reply:

The etrailer Trailer Hitch Receiver # e98844 referenced in your question is confirmed to fit the 2014-2019 Toyota Highlander. It fits with the full-sized spare tires under the Highlanders as long as they are not on the aluminum rims.
The aluminum rimmed spares are too wide so you would not be able to store the tire underneath the vehicle after installation. The full-sized steel spares fit fine.

I have attached an installation video on a 2019 Toyota Highlander for you to check out.

expert reply by: Chris R

0

Answer 1

The U-bolt for this replacement cradle would only be stable on a round tube. I would recommend a bike rack that mounts on your ball mount instead of on your kayak trailer. You might try the 4-Bike Swagman #S64675. Another option is a truck bed rack…

view full answer...

Answer 2

If your 2008 Toyota Highlander has a converter box under the dashboard already then you have the factory tow package. To give you an idea of what to look for I've attached a video of the trailer wiring being installed onto a Highlander without…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 6

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...