Inside Tube Size of MaxxTow Adjustable-Height Ball Mount MT70068

Question

Question:

What is the tube size of the adjustable piece? I was thinking of using this in order to vertically mount an empty hitch basket when it is empty. I also happen to have a vertical receiver hitch on another vehicle which needs a ball mount anyway and thought I could kill two birds with this. Thanks for your time!

asked by: Eddie

0

Expert Reply:

Both the shank portion and the ball mount portion of the MaxxTow Adjustable-Height Ball Mount # MT70068 measure 2- x 2-inches. I confirmed this by going to our warehouse and measuring both parts for you.

expert reply by: Adam R

0

Answer 1

We offer replacement rollers that could help with your situation like the part #295-000177 but what I would recommend is have your tech check out the link I attached to this page that has all of the rollers we offer and have him pick out what your…

view full answer...

Answer 2

It sounds like you have corrosion compacted in the weldnuts on your 2009 Toyota Sienna. All you can do is spray the lubricant, let it sit from about 15 minutes, and then go at the weldnuts with a wire brush. Do this repeatedly. If that doesn't…

view full answer...

Answer 3

I would retap the threads with the next size up. Which from my research would be M12-1.5. If you are still unsure you can take the bolt you have with you to a hardware store, tell them you are in need of a tap that is the next size up, and they will…

view full answer...

Answer 4

Since tapping new threads can result in threads that are not cut straight I recommend taking some steps to clean out the weldnut on your 2002 Toyota Highlander before attempting to tap new threads. What you can do is use some spray lubricant like…

view full answer...

Answer 5

The Curt Class III Trailer Hitch part #C13105 for the 2008 Toyota Sienna utilizes M12 bolts. It sounds like you have already tried to use a brush like part #814092 and Blaster Lubricant or WD-40. You can tap out the weldnuts with a M12x1.25mm tap…

view full answer...

Answer 6

The MaxxTow Adjustable Ball Mount, Part #MT70068, has a distance from the center of the hitch pin hole to the upright of 8-1/8 inches. This part includes both a 1/2-inch pin and clip to secure the ball mount, and a 5/8-inch pin and clip to secure the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Inside Tube Size of MaxxTow Adjustable-Height Ball Mount MT70068

Product Page this Question was Asked From

Continue Researching