Tap Size One Size Bigger than M12 - 1.25 for Hitch Install with Stripped Nut
Question:
I stripped two of the nuts on the Sienna. Cleaned them all and chased the threads with an M12 - 1.25 that I purchased for this purpose. Unfortunately when torqueing, two just kept turning. My Dilemma I understand the re-taping concept. My concern is the thickness of the walls of the nut. if I re-tap the next size up, then I am losing the least amount of wall steel on the nut. if I go to a helix coil then I fear that I am taking too much steel away and the nut may crack or fail in the end do you have some practical advice on this. what is the next size up, 1/2? I assumed that you have run into this situation. thanks, ps I already read the articles on this on your site.
asked by: Thomas M
Expert Reply:
I would retap the threads with the next size up. Which from my research would be M12-1.5. If you are still unsure you can take the bolt you have with you to a hardware store, tell them you are in need of a tap that is the next size up, and they will set you up.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: MaxxTow Adjustable-Height Ball Mount Review
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 7-1/2" Drop, 6-1/4" Rise - 5,000 lb
- Article: How to Measure for Trailer Hitch Drop
- Search Results: hitch pins and clips
- Search Results: maxx tow
- Q&A: Does Longer Shank of MaxxTow Adjustable-Height Ball Mount MT70068 Affect Capacity of Hitch
- Video: Draw-Tite Ball Mount Review - 2006 Toyota Sienna
- Video: Flint Hill Goods Adjustable Ball Mount Review FHG25VR
- Video: etrailer Trailer Hitch Installation - 2017 Toyota Sienna e98837
- Video: Trailer Wiring Harness Installation - 2009 Toyota Sienna
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Flint Hill Goods Adj Ball Mount - 2" Hitch - 10" Drop/8" Rise - 5K
- Shop: Hitch Pin and Clip for 2" Hitches - 5/8" Diameter x 2-7/8" Span
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: etrailer.com Trailer Hitch Installation - 2006 Toyota Sienna
- Search Results: 98853
- Search Results: e98853
- Q&A: Tap Size For Weldnuts In 2008 Toyota Sienna To Install Curt Hitch
- Q&A: Can't Thread in Trailer Hitch Bolts on a 2009 Toyota Sienna
- Q&A: Cleaning Out Corroded Weldnuts to Install a Trailer Hitch on a 2006 Toyota Sienna
- Video: Trailer Hitch Installation - 2004 Toyota Sienna - Curt C13105
- Q&A: What Kind Of Bolts Are Used In The Replacement Hardware Kit For Curt SecureLatch Pintle Mount?
- Q&A: How to Wire Electric Brakes on a Tandem Axle Trailer
- Shop: Suspension Enhancement
- Search Results: leaf spring bushings
- Q&A: How to Install Trailer Hitch on Vehicle with Stripped Weld Nut