Extra Long Coiled RV Style 7-way Connector

Question

Question:

Item # WG54006-043, 7 way RV style connector/with 6foot long coiled cable-trailer end. I am looking for this very cable, however I need the trailer end to be 4foot long after the coil. Can you have this custom made or can you direct me to the manufacturer so that I can call or write them directly?

asked by: Philip A

0

Expert Reply:

We do have longer connectors, like the WesBarg 7-Way, RV-Style Connector # WG54006-046 which is 12 feet long.

We also have connectors that aren't coiled like the Bargman 7-Pole, RV-Style Connector - Trailer End # 50-67-103 which is 15 feet long.

expert reply by: Charles S

0

Answer 1

In general terms, when you have a red wire on a 7 way connector it is typically going to be the left hand brake and turn signals. With that being said, it's probably more important to note where it is connected since this will determine what…

view full answer...

Answer 2

If you can hear the magnet working then the issue is most likely in the brake adjustment/installation. Please verify that installation is correct then make adjustments. For self adjusting brakes such as Dexter Nev-R-Adjust Electric Trailer Brake…

view full answer...

Answer 3

The black wire from the break away switch will connect to the blue wire from the break away box, as shown in the provided diagram. By 'brake wires' I'm assuming you're speaking of the wires connected to the brake magnets on your brake…

view full answer...

Answer 4

You don't have to install a junction box when you install the #50-67-103 on your trailer. If you wanted, you could just run the wires to each function as needed. The black wire of this connector would be the one to use for the charge wire of your…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

When wiring a trailer connector, it is best to wire by function, as wire colors can vary. We have an excellent wiring diagram on our website, I will provide you a link so you can look at it. If you are looking at the inside of the trailer connector…

view full answer...

Answer 8

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

You have it right so far, the 4-way connector is just as you have stated. Remember that Yellow has a L in it so that is the left side brake/turn signal and green has a R in it so that is the right side brake/turn signal. The colors for wiring a 7-way…

view full answer...

Answer 11

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...