Locking Trailer Door Latch with Inside Release to Fit 3-3/8 inch by 4-5/8 inch Opening

Question

Question:

I am looking for a stainless steel locking paddle latch with an inside release. You carry the junior but I cant find the large one on your website. The one I need is 4.25 x 5.50 inches and fits in a 3 3/8 x 4 5/8 hole. Thanks for any help.

asked by: Kenny

0

Expert Reply:

The Full Size Locking Steel Flush Door Latch # L3980 fits into a 3-3/8 inch by 4-5/8 inch opening on your trailer, however it isn't stainless steel. It does have a stainless spring and rustproof finish.

Use the Inside Knob # 4PLSP to allow you to open the latch from inside your trailer.

expert reply by: Charles S

0

Answer 1

I did some research on the Bargman L-300 lock that you mentioned in your question, and it appears that these have not been made in a long time. Specific replacement parts for this particular line are no longer produced. If you are needing to replace…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Although we don't carry replacement parts for your Reliable brake actuator we do offer a good replacement, the Dexter #DX89FR would be an excellent replacement for your current actuator. You can see a product video for the #DX89FR hydraulic…

view full answer...

Answer 4

To create barn doors out of your ramp door, you will need hinges and a latch. I suggest a latch/lock system like the Universal Cam-Door Lock for Enclosed Trailers - 1" Keeper, #383200. This will use a 3/4 inch diameter pipe that you'll have…

view full answer...

Answer 5

Hey Lou, so the install of the Conventional Ramp Door Spring part #362SA7218 is something that should be done by someone who has experience winding garage springs. The amount of turns or preload will be the amount that gives you the correct amount of…

view full answer...

Answer 6

I spoke with my contact at Dexter and he said the 21-37 oil cap is obsolete and was replaced with the 21-36 oil cap, #RG04-270. This cap includes the o-ring and plug.

view full answer...

Answer 7

The Bargman L-300 lock is no longer manufactured so a direct replacement lock is not available. The Redline Full Size Locking Steel Flush Door Latch #L3980 that you referenced has a similar handle lock design and should work nicely as a replacement.…

view full answer...

Answer 8

34 inch frame hitch fits are for the cab and chassis model trucks. The part #C15312 does not fit cab and chassis model trucks so it would not be a fit for a 34 inch frame. The part #C15800 is an example of a Curt hitch that does fit a 34 inch wide…

view full answer...

Answer 9

The Redline Flush Mounted Door Latch, #L3980, will mount in a door that has a 3-3/8 x 4-5/8 inch mounting hole. This latch is rust proof and will attach to the door using screws instead of pop rivets. If this latch cannot fit into your door's…

view full answer...

Answer 10

I might have an option for you but we don't offer any flush door latches with an extended striker. However, the Full Size Locking Steel Flush Door Latch part #L3980 matches your door cutout at 4-5/8" long x 3-3/8" so this is our best…

view full answer...

Answer 11

For the size you listed it sounds like you need a full-sized door latch like the part #L3980 that mounts in door openings that are 3-3/8" x 4-5/8" hole. This is a very common door latch seen on horse trailer as well.

view full answer...

Answer 12

The appropriate torque spec for any application will vary depending on the construction of the wheel as well as on the stud size. I suggest checking the wheels you're using to see if their manufacturer has a suggested torque rating. Steel trailer…

view full answer...