Does Tekonsha Breakaway Kit with Integrated Charger Meet DOT Requirements

Question

Question:

Breakaway kits. the breakaway kit that has a separate charger says it is DOT compliant. The breakaway kit with the integrated charger says nothing about DOT. I am loking at the Teconsha sp brand. my question is : is the breakaway kit with the integrated charger DOT compliant? If not, then why?

asked by: Matthew C

0

Expert Reply:

I just verified with Tekonsha that the Breakaway Kit with the Integrated Charger # 50-85-313 does meet all DOT requirements.

expert reply by: Charles S

0

Answer 1

According to Curt, their #C52042 Trailer Breakaway Kit is compatible with single, tandem or tri axle trailers. I've inked to a product demonstration video that you might find helpful.

view full answer...

Answer 2

If all 3 of the trailer axles have brakes you will need one with enough amperage to be able to apply the trailer brakes on full for at least 15 minutes. The Tekonsha system, #50-85-313 will work with 1 to 3 axles. I have included a link to a video…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

You're correct. The repalcement for your existing B12EA-22 brake would be #AKEBRK-7R-SA for the right side and #AKEBRK-7L-SA for the left.

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

We do have replacement options for the Jensen JRV9000 though they are not touchscreen or video compatible. The JRV9000 is a double din so you will need to replace it with such like the Jensen RV Stereo part #JWM60A which is a more basic model. The…

view full answer...

Answer 7

In regards to an electric over hydraulic actuator, the 1,000 psi model is for drum brakes and the 1,200 psi model is for disc brakes. The size of the axle, etc. are not factors. The most popular option we offer is the HydraStar Vented Marine Electric…

view full answer...

Answer 8

The pictures for wheel stud set #RG03-080 are more of a typical photo. The actual design is the same as #165995. I pulled a set from the warehouse to be sure and they are indeed like #165995.

view full answer...

Answer 9

A TruRyde rvd-h-865 7k hub/drum like # AKHD-865-7-2-K uses 1/2-inch drive-in studs that are 1-5/16-inches long. For a replacement stud you can use #165981. This is slightly longer at 1-1/2-inches but it has the same 1/2-inch diameter. They are also…

view full answer...

Answer 10

The three wires of the Tekonsha Breakaway System part #50-85-313 will get wired as follows: The white wire attaches to the ground wire. The blue wire attaches to the brake output circuit that goes to the brake assemblies of the trailer. The black…

view full answer...

Answer 11

That's a good question, because working load limits (WLL) can be somewhat confusing, but I can explain it for you. The 9,200 lb WLL of the Titan Chain Ratcheting Load Binder for 3/8" - 1/2" Thick Chain #TCRB10 simply means that the…

view full answer...

Answer 12

The only difference in the Demco Channel Tongue Trailer Couplers #DM16080-95 and #DM15931-95 is going to be the bolt pattern. One will have the 5-Bolt hole pattern and the other is going to have 4-Bolt holes. I have included images below showing the…

view full answer...