Replacement Trailer Brake Assembly for B12EA-22 on 2018 Forest River 294BH Travel Trailer

Question

Question:

I have e a 2018 Forrest River 294BH Travel Trailer. The current brakes on it are B12EA-22. Etrailer does not list my trailer model nor the model number for the brakes. When I search for B12EA-22 it shows me AKEBRK-7R-SA. Are those the ones I need?

asked by: Christopher K

0

Expert Reply:

You're correct. The repalcement for your existing B12EA-22 brake would be # AKEBRK-7R-SA for the right side and # AKEBRK-7L-SA for the left.

expert reply by: Mike L

0

Answer 1

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 5

The correct set of replacement brake assemblies for your AxleTek 12 inch assemblies is the kit part #AKEBRK-7-SA that you referenced. This kit is a pair of left and right assemblies that are an exact match to what you have that are also self…

view full answer...

Answer 6

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Answer 10

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 11

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Replacement Trailer Brake Assembly for B12EA-22 on 2018 Forest River 294BH Travel Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching