Does Curt Hitch C11327 Fit a 2006 Honda Accord Sedan with Dual Exhaust

Question

Question:

I own a 2006, Honda Accord EX/XL, not sure which, sedan with 6 cyl DUAL EXHAUST. Your pictures show installation on a single exhaust vehicle. As far as I can tell. What, if any, modifications are required for a dual exhaust? Thank you for your time and consideration.

asked by: Phyllis

1

Helpful Expert Reply:

To install the Curt hitch part # C11327 on a dual exhaust version of the 2006 Honda Accord Sedan really wouldn't be that much different than a single exhaust. We had a customer come back and write a review for this hitch and he mentioned that he had a dual exhaust model and he made no mention of any special steps needed.

I attached an install video for this hitch on a 2006 Honda Accord just like yours.

expert reply by: Jameson C

1

Answer 1

The furthest two attachment points for the cross tubing on Curt Hitch, #C11290, are in the trunk pan (where the spare tire sits) and not the frame. The attachment point for the bracket nearest the receiver opening is a tow hook near the center of the…

view full answer...

Answer 2

I spoke with my contact at Curt regarding the Trailer Hitch Receiver #C11327 on your 2007 Honda Accord. He stated that while they have not heard of any issues like what you are describing with the small gap between the carriage bolt and tow loop on…

view full answer...

Answer 3

Unfortunately we only carry Class I Hitches with a 1-1/4" receiver for your 2006 Honda Accord Sedan. This is because your vehicle has a Gross Towing Weight Capacity of 1,000 lbs. and a Tongue Weight Capacity of 100 lbs. The hitch I recommend for…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 7

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 11

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Does Curt Hitch C11327 Fit a 2006 Honda Accord Sedan with Dual Exhaust

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching