Why Would Nutsert Pop Out of Tailgate After DeeZee Tailgate Assist Install

Question

Question:

I just installed this last night and the bolt that goes on my tailgate bent and popped out soon as I let the tailgate down I tried to use Teflon tape but it seems as if something is wrong with the inside part thats attached now to my tailgate ..... Should I buy parts kit and try again?

asked by: Kevin

0

Expert Reply:

Looks like you overtightened the nutsert which stripped it out and rendered it unusable.

You would need to order the part # BKT43301 and be careful not to strip out the new nutsert.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I believe you are asking about ordering the nutsert and replacement tool for the DeeZee Tailgate Assist #DZ43301. The only way to get that is with the #BKT43301 that you referenced.

view full answer...

Answer 2

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 3

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 4

Yes, you can use the NOCO GEN On-Board Battery Charger #NOC34FR on your pickup's parallel batteries without disconnecting them. If your batteries were in a series, they would have to be disconnected. Since your batteries are parallel and maintain…

view full answer...

Answer 5

In order to charge your batteries wired in parallel with the NoCo Genius #329-GENIUS5 you'll want to connect the positive charge line to the positive terminal of the first battery and the negative line to the negative terminal of the opposite…

view full answer...

Answer 6

The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to check…

view full answer...

Answer 7

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 8

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 9

For your 2010 Forest River R-Pod 172 that has 3,500 lb Lippert torsion axles the correct lift kit is the #LC382741 that you referenced which will give you a 3-1/2 inch lift.

view full answer...

Answer 10

I do have an option for you but the Stromberg Carlson 4000 Series 5th Wheel Louvered Tailgate part #VGD-10-4000 does not have a spot for the factory backup camera. Therefore you would either need to find a way to mount this yourself, go without, or…

view full answer...

Answer 11

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 12

The B&W Companion OEM 5th Wheel Trailer Hitch #BWRVK3700 is perfectly compatible with cushioned pin boxes like your MORryde RP072-1621HD, so the clunking you're experiencing isn't related to the two components being incompatible. With…

view full answer...

Why Would Nutsert Pop Out of Tailgate After DeeZee Tailgate Assist Install

Product Page this Question was Asked From

Continue Researching