Fit of Curt #12064 on Challenger SXT V6 2015

Question

Question:

Hi! Can you provide a picture of the Curt #12064 installed on a 2015 Dodge Challenger? The new rear bumper fascia is different, and I hope it look similar to the Charger 2014. Thank you for your help

asked by: Patrick

0

Expert Reply:

I spoke with my Curt representative about the fit of their # C12064 Class II hitch on a 2015 Dodge Challenger. Although they don't have any photos available (we don't either), I was told that although there were cosmetic changes made to the rear of the 2015 Challenger, the fit itself hasn't changed. The hitch will fit without needing to alter the rear bumper fascia.

expert reply by: Mike L

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 4

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 5

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 9

You can get a new brake mounting flange for your axle. The old flange will need to be cut off. The part is #4-44-1. This is designed to fit a 3 inch trailer axle and should be welded in place by a professional. Since you would also have to get the…

view full answer...

Answer 10

In regards to the Correct Track Trailer Alignment and Lift Kit part #RR23QX, the kit provides a lift by essentially extending the hangers. This normally requires cutting off the old hangers and welding on new, taller ones but with this kit you…

view full answer...

Answer 11

The Correct Track Trailer Alignment and Lift Kit - Tandem Axle #RR23QX does come with all of the components needed to lift a tandem axle trailer. The center hangers of a tandem axle setup use different components than the front and rear hangers since…

view full answer...

Answer 12

The Correct Track Trailer Alignment and Lift Kit part #RR23QX offers a 1-1/4" or 2-1/4"lift so if the hitch height height is lower than the vehicle hitch height you can use this kit to bring the trailer level with the vehicle and eliminate…

view full answer...