Ford Ranger Trailer Wiring Recommendation

Question

Question:

Can a 1997 Ford Ranger accept trailer light loading with no overload issues?

asked by: TWR

0

Expert Reply:

The recommended trailer wiring harness for your 1997 Ford Ranger is the Tow Ready # 118325. As long as you don't exceed the amperage ratings of the wiring (Stop/turn lights: 2.1 amps per circuit and Tail lights: 4 amps per circuit), you would be just fine.

expert reply by: Jameson C

0

Answer 1

I would first start by testing the wires on the T-connector with a circuit tester like the Quickee, #3808, to make sure that each is functioning as it should. If there is an issue with any of the wires, you will need to replace the T-One Vehicle…

view full answer...

Answer 2

The Curt Class II Trailer Hitch, part #12012 mounts to the frame members under the rear of the bed. The frame members would be the same for that model year, regardless of the bed. You should have no fit issues with this hitch. Keep in mind that Curt…

view full answer...

Answer 3

The Curt Trailer Hitch Receiver part #C11576 which fits your 2019 Toyota Camry comes with what is referred to as a powder coat finish. A powder coat finish is similar to paint in look but is much more weather resistant. I do not have any quantitative…

view full answer...

Answer 4

For your 2002 Ford Ranger with the Flareside or Stepside bed, I recommend the Draw-Tite Class III Max Frame Receiver Hitch #75082. This Class III hitch is confirmed to fit your truck and will use existing holes in the vehicle frame to ease the…

view full answer...

Answer 5

We have found the Tekonsha wiring products, like the T-One #118325 for your 1997 Ford Ranger, to be the most reliable out of all of the wiring options we carry. With that being said if 2 different local shops are thinking that your ECM is the issue…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 11

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 12

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Ford Ranger Trailer Wiring Recommendation

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching