Trailer Hitch Fit on 2004 Chevrolet Astro Van with Full-Size Spare Tire

Question

Question:

Hitch c13035 work with full size spare on 2004 astro?

asked by: Bernard K

0

Expert Reply:

The Curt Class III hitch # C13035 will very likely have interference with a full-size spare, but we do offer both 1-1/4-inch Class II and other 2-inch Class III hitches that do not have this fit issue.

The included link will show you three choices in a 1-1/4-inch Class II hitch.

If you prefer a 2-inch Class III that does NOT cause spare tire interference you can use Draw-Tite # 75122. An install video on an Astro van is linked for reference.

expert reply by: Adam R

0

Answer 1

For your 2002 Chevrolet Astro I recommend the Curt Trailer Hitch Receiver #C13035. This custom fit Class III hitch has a 2" receiver and a bolt-on installation. It features a concealed cross tube so only the receiver will be visible from the…

view full answer...

Answer 2

The Draw-Tite 75122 will fit your 2001 GMC Safari. The different weight ratings are provided in the event that a weight distribution system is needed. The hitch, when used with a standard ball mount and ball, has a 5,000 pound gross towing weight…

view full answer...

Answer 3

TheDraw-Tite Max-Frame Class III Trailer Hitch, item #75122, will fit the standard chassis Chevrolet Astro as well as the extended Chassis. I spoke with my contact at Hidden Hitch and on the 2000 model Astro with a standard chassis the spare tire…

view full answer...

Answer 4

Most of the trailer hitches offered for your 1998 Chevrolet Astro Van, which can be seen on the link provided, feature one-piece welded construction. One exception is the Curt #C13035, which has bolted-on mounting flanges. The two mounting flanges on…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...