Is there a Front Mount Hitch Available for a 2005 Ford F-250 XLT Super Duty

Question

Question:

Can this hitch be installed on the front of my truck? Ford F250 XLT Super Duty 2005. If not do you have one that can be?

asked by: Tom R

0

Expert Reply:

For your 2005 Ford F-250 XLT Super Duty, I recommend the Draw-Tite Front Hitch, # 65022, which is designed to be mounted in the front of your vehicle. If you have the optional OEM fog lights on your truck, you must remove or relocate them for receiver installation. I have included a link to the instructions below.

expert reply by: Michael H

0

Answer 1

The Draw-Tite 2-Inch Front-Mount Hitch, part #65022, will fit the Ford Super-Duty pickups for model years 1999 through 2007. It is compatible with pickups that are equipped with tow hooks (but these will need to be removed temporarily and…

view full answer...

Answer 2

This is correct. If you have the Blocker Beam on your 2006 Ford F-350 you will need to use the Draw Tite hitch #65022 or if not you'd need the #31114. The blocker beam is a small sub-bumper behind air dam.

view full answer...

Answer 3

The Curt Front Mount Trailer Hitch Receiver part #31114 which is a fit for a 2007 Ford F-250 Super Duty installs behind the bumper beam to the end of the frame on both the driver and passenger side. I have attached a photo below which shows this.…

view full answer...

Answer 4

Since your truck bed is occupied by your 5th wheel hitch and since there are no 5th-wheel-mount kayaks carriers the best option is to use a front-mount hitch such as #65022 along with a load support like #EM07605. This would put much of the…

view full answer...

Answer 5

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 6

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Is there a Front Mount Hitch Available for a 2005 Ford F-250 XLT Super Duty

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching