Replacement Spring Bars for Equal-i-zer Weight Distribution Systems - Qty 2 - 1,000 lbs TW

See what our Experts say about this Equal-i-zer Accessories and Parts

• How To Upgrade from the 600 Lb to 1,000 Lb Equal-i-zer Weight Distribution System
  The Replacement Socket for Equal-i-zer 1,000 Lb Weight Distribution Systems part # EQ90-03-1000 is larger than the Replacement Socket for Equal-i-zer 600 Lb Weight Distribution Systems part # EQ90-03-0600 therefore, it cannot be used with the Replacement Head for Equal-i-zer Weight Distribution Systems part # EQ90-02-0600. If you need to upgrade to the 1,000 lb system from the 600 lb system then you will need the Replacement Head for Equal-i-zer Weight Distribution Systems part # EQ90-02-1000...
  view full answer...
• Upgrading the Equal-i-zer Weight Distribution System
  Yes, you are correct in that you will need to upgrade your spring bars if you have exceeded the tongue weight capacity of your weight distribution system. However, the Replacement 1,000 Lb. Spring Bars for Equal-i-zer Weight Distribution Systems part # EQ90-01-1099 are 1-3/8" wide and the the Replacement 1,200 Lb. Spring Bars for Equal-i-zer Weight Distribution Systems are 1-1/2" wide. Therefore in order to upgrade the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control part...
  view full answer...
• Can You Switch Between 10K and 12K Equal-i-zer Weight Distribution Systems
  The 10K and 12K Equal-i-zer Weight Distribution Systems like part # EQ37100ET and part # EQ37120ET use different heads and spring bars so if you wish to switch back between the two capacities you will need both of these items which I have listed for you below. Equal-i-zer 10K Head part # EQ90-02-1000 Equal-i-zer 10K Spring Bars part # EQ90-01-1099 Equal-i-zer 12K Head part # EQ90-02-1200 Equal-i-zer 12K Spring Bars part # EQ90-01-1299
  view full answer...
• What Spring Bars for Equal-i-zer Weight Distribution are Needed for Keystone Springdale 1750RD
  If the weight of the trailer is over half the weight of the tow vehicle then you'll need a weight distribution system. The rear suspension on the Ram also uses coil springs which are great but they'll sag more than the comparable leaf springs on a Ford or Chevy. Furthermore, the lighter trailers are typically the ones with sway control problems so I do think a weight distribution system is a good idea for you. That said, an overrated one won't do you any good so you'll want to replace the...
  view full answer...
• Replacement Frame Brackets and Spring Bars for 10K Equal-i-zer Weight Distribution System
  If you're looking for replacement frame brackets for an Equal-i-zer Weight Distribution System then we have just what you need in the Replacement Sway-Control Bracket for Equal-i-zer Weight Distribution part # EQ95-01-5600. We also carry the spring bars as well as the Replacement Spring Bars for Equal-i-zer Weight Distribution Systems part # EQ90-01-1099.
  view full answer...
• What is the Width of the Equal-i-zer Replacement Spring Bars
  I went out to our warehouse and pulled the Replacement Spring Bars for Equal-i-zer Weight Distribution Systems - Qty 2 - 1,000 lbs TW, # EQ90-01-1099. The bars actually measure 1-3/8 inches wide. I also checked with Equal-i-zer and this product is confirmed to replace the spring bars on your system.
  view full answer...
• Equal-I-Zer Weight Distribution is Too Stiff; Can Lighter Bars be Used in the Same Head
  The different size Equal-I-Zer systems have heads to match the bar sizes so the parts are not interchangeable. But not to worry, with some adjustment you can soften it up a little and not have to use a different system. You will need to lower the tension on the spring bars. To do this you can angle the head towards the trailer and/or mount the parts of the brackets that hold the spring bars one slot lower. This will lower the tension and soften up the ride. Try this first instead of going...
  view full answer...
• Replacement Spring Bars for Equal-i-zer Weight Distribution System With 1-1/4 Inch Wide Opening
  If the socket heads for your Equal-i-zer Weight Distribution System are 1-1/4" wide then that means you have the Equal-i-zer Weight Distribution System part # EQ37060ET and the correct replacement for this is the Replacement Spring Bars for Equal-i-zer Weight Distribution Systems part # EQ90-01-0699. The next closest size is 1-3/8", the Replacement Spring Bars for Equal-i-zer Weight Distribution Systems part # EQ90-01-1099
  view full answer...
• Replacement Spring Bars for 1,000 Pound Equal-i-zer Weight Distribution System
  The Replacement Spring Bars # EQ90-01-1099 are the correct replacement bars for your 1,000 pound Equal-i-zer weight distribution system. This will include 2 spring bars. The part # EQ90-02-1099 referenced in your question is the same product, however it only includes one spring bar. That is the only difference between the two parts.
  view full answer...
• Replacement Equil-i-zer 1,000 lb Tongue Weight Spring Bar Compatibility With 1,200 lb System Head
  The Replacement Spring Bars for Equal-i-zer Weight Distribution Systems - Qty 2 - 1,000 lbs TW - # EQ90-01-1099 are 35-1/2 inches x 1-1/2 inches so they can be used with the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 12,000 lbs GTW, 1,200 lbs TW # EQ37120ET head and brackets. Replacing these spring bars will lower your capacity and in this case, give you a smoother and more controlled ride.
  view full answer...
• How Can I Determie Which Replacement Spring Bars I Need for My Equal-i-zer WDS
  The Replacement Spring Bar for Equal-i-zer Weight Distribution Systems # EQ90-02-0699 could potentially work however without knowing what system you currently have I won't be able to say for certain. The easiest way to find out what you need is to just measure the inside hole on the head where the spring bars would go. If you measure 1", then you'd want # EQ90-01-0499, if you measure 1 1/4" then you'd want # EQ90-01-0699, if you measure 1 3/8" then you'd want # EQ90-01-1099, and finally...
  view full answer...
• Replacement Spring Bars for Equal-i-zer 10,000 Lb Rated Weight Distribution System
  We do offer the replacement spring bars for the Equal-i-zer 10,000 GTW/1000 lb TW weight distribution kit as part # EQ90-01-1099. The bars are sold in pairs. These will replace missing spring bars for a 10K GTW/1K TW Equal-i-zer system, but they CANNOT be used to upgrade a lower rated system as the weight distribution head is different and the bars aren't interchangeable. If you're needing to upgrade from a lower rates system, you'll need a new system like # EQ37100ET.
  view full answer...
• How can I Determine Which Size Spring Bars I Need for My Equal-i-Zer WDS?
  It is not going to be stamped on the bars, unfortunately, The easiest way to determine which spring bars you have is to measure the inside hole on the head where the spring bars would go. If you measured 1", then the correct bars you'd need are the Replacement Spring Bars for Equal-i-zer Weight Distribution Systems # EQ90-01-0499; If you measured 1-1/4", then the correct bars you'd need are the Replacement Spring Bars for Equal-i-zer Weight Distribution Systems # EQ90-01-0699; If your...
  view full answer...
• How to Select Weight Distribution System for Use with Multiple Trailers
  Weight distribution/sway control (WD/SC) systems really need to be tuned to the actual tongue weight (TW) of the fully-loaded trailer, with all cargo and supplies in place and with tanks filled. Different systems have spring bars that are rated for a specific TW range, usually a range of several hundred pounds. It is possible to select a system now for your current pop-up, and when the time comes to get a new larger trailer just change the spring bars to a set that is rated appropriately...
  view full answer...
• Can Spring Bars of Equal-i-zer Weight Distribution System be Changed to Change Rating
  Yes, you can just replace the spring bars and head of your current system to change the weight rating. All you would need is the part # EQ90-01-1099 for a set of bars and # EQ90-02-1000 for the head that are rated lower at 1,000 lbs tongue weight.
  view full answer...
• Recommended Replacement Spring Bars To Accommodate Lighter Trailer
  Your weight distribution system, # EQ37120ET, is rated for a total tongue weight of 800-1200 lbs. That total tongue weight is the loaded tongue weight of your trailer as well as any cargo behind the rear axle of your tow vehicle. I've attached an article on trailer tongue weight to help. If you are at 15% of tongue weight you'll be in that range, but lighter would be a rough ride. I recommend using a scale like # e99044 to determine your actual loaded weight. I've attached an article...
  view full answer...
• Best Equal-i-zer Weight Distribution System for 9k GVWR Travel Trailer
  The tongue weight range for the # EQ37140ET is 1,000-1,400 lbs and I'm assuming this is the system you're referring to. We recommend measuring your loaded tongue weight of your setup to see if it will fall in that range. Even with 800 lbs as your dry tongue weight, the system may be overrated. The sway control would work, but an overrated system could cause a rough ride and bouncy trailer. If you measure and find that it does fall into that range then you are good to go. I also see you...
  view full answer...
• Are Replacement Weight Distribution Spring Bars Available as Single Bars or Pairs of Bars
  Some replacement spring bars for weight distribution systems are sold as a single bar while others are sold as a set of two. It will depend on the brand and the specific model system. For example, the Husky Center Line bar # HT32329 is sold as one bar while the Equal-I-zer part # EQ90-01-1099 is sold as a set of two. All such bars are shown on the linked page.
  view full answer...
• Are Spring Bars on Equal-i-zer Weight Distribution System Interchangeable?
  You would not be able to simply replace the spring bars on your Equal-i-zer # EQ37060ET weight distribution hitch. Instead you would need to get both the 1,000 lb tongue weight spring bars # EQ90-01-1099 as well as the 1,000 lb head unit # EQ90-02-1000.
  view full answer...
• Are Equal-i-zer Spring Bars Interchangeable With Same Head Unit?
  It is possible for some spring bars to be interchanged based on their size, but that won't increase a weight distribution system's capacity without adding the appropriate head unit. The replacement spring bars that are rated for 1,200 lbs TW and 1,400 lbs TW have the same dimensions, but the spring bars rated for 400 lbs TW, 600 lbs TW and 1,000 lbs TW are different, as you can see below. Replacement Spring Bars for 400 lbs TW, # EQ90-01-0499: 35-1/2 inches x 1-inch Replacement Spring...
  view full answer...
• Are Stability Plus Stabilizers Compatible With A 2022 Ford F-150 With CCD Suspension
  The Ford Continuously Controlled Damping (CCD) system is simply a computer that adjusts the valves inside of your shocks to absorb road shock so it wouldn't be in the way and neither would the onboard scale feature. So yes, you could install the Stability Plus Stabilizer Helper Springs # SPS94FR (4WD) or the # SPS57FR (2WD). These sit on your leaf springs, pulling them back for more support so you can end up with a stiffer ride when not hauling any weight since these can't be easily adjusted. If...
  view full answer...
• Dimensions of Equal-I-zer Spring Bars EQ90-01-1099
  The Spring Bars for Equal-i-zer Weight Distribution Systems # EQ90-01-1099 are the same as those included in the complete 10K system # EQ37101ET. I measured these bars with a digital caliper to get you accurate dimensions. The dimensions of the end of these bars that enters the head assembly is 1.35 x 1.35-inches (or 34.5mm x 34.5mm). These fit the head assembly # EQ90-02-1000.
  view full answer...
• How To Determine What Size Replacement Spring Bars Are Needed For Equal-I-zer Weight Distribution
  The easiest way to determine what replacement spring bars you need for your Equal-I-zer weight distribution system is to take a simple measurement. Just measure the inside of the hole in the head where the spring bar is inserted. If it is 1-3/8 inch then the system is a 10,000-lb system with a 1,000-lb tongue weight. You would need part # EQ90-01-1099. If the hole measures 1-1/2 inches it will be the 12,000 or 14,000 system that has a 1,400-lb tongue weight, and the replacement spring...
  view full answer...
• Replacement Bars for an Equalizer Hitch, 14,000 to 10,000 Solution
  At one point Equal-i-zer bars could be swapped easily to convert a kit to a higher/lower tongue weight range, but we now know that you have to replace the head of the unit with the bars. So with the bars part # EQ90-01-1099 that you need you will need to swap the head # EQ90-02-1000 in as well. Also if you are getting persistent sway try moving more weight of the trailer up to the front to increase the tongue weight as that typically is the easiest fix for sway.
  view full answer...

Do you have a question about this Accessories and Part?