Summer Starts Here - Save up to 70%
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.
Features:
Specs:
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
Average Customer Rating: 5.0 out of 5 stars (11 Customer Reviews)
Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.2019 Honda Ridgeline RTL-E. Installed it myself but a helper would have made it easier. Instruction say to remove and discard the lower engine shroud before mounting. I chose to do surgery on the shroud to fit the attachment points and put it back in. This made the install harder (less finger room) but the result in very nice. I measured clearance before and after at the lowest part of the engine. Putting this on reduced overall clearance 1 inch. It changed angle of attack significantly. Here's what you should think about...Is this a vehicle for serious 4 wheeling in? Then don't do this. And buy a different truck with greater ground clearance. If, like me, you pull a small trailer on paved and gravel roads, and you want to put bikes on the front, this will work great. See pictures attached.
Love my Ridgeline. But the only hard point in the front is buried deep under the engine. This provides three rescue points and a way to mount a winch or whatever with a 2” hitch mount. Here is the good and bad. Etrailer.com was perfect. Fast shipping, good communication.five stars. The quality and value of the hitch is top notch. Holes lined up perfectly. All hardware was provided and high quality. Now the less than ideal. The hardest part of the installation was getting the rivnuts set. They wanted to spin in the holes. I had to rig a little tool out of a long eyebolt, screw it into the rivnut and run a nut up against the mount with a fair amount of muscle to expand the anchor. The other quip I have is that the hitch is very low. If I I mount a bike rack or something I’ll have to add a riser. The hitch comes out under the bumper and Honda didn’t go for maximum clearance. Ideally a hitch would come out though the bumper at a more appropriate height. But that would require a great deal of modification to the truck. I can’t fault the seller or the hitch manufacturer for these issues. Rivnuts are just work to set without the specialized tool and Honda gave us a pretty low front end. Moreover I am happy with the upgrade and feel better having a way to mount loads up front or attach a rescue strap.
Received the hitch a couple days late due to UPS issues. Followed the instructions which were fairly easy to follow. The pictures were a bit dark and difficult to view but I was able to figure what to do once I got underneath and compared the hitch alignment to the corresponding bolts. I did place my truck on ramps but still a little uncomfortable laying on my back and doing the work. Used a lift to position the hitch which was a little precarious. I didn’t have any help which would have been nicel. I struggled with the last of the bolts to screw in properly so had to loosen others and work a pry bar to get it to thread properly. Finally all bolts threaded well and able to tighten securely. Thought about refabing the plastic shield instead of discarding it, which maybe was possible, but didn’t have the energy.
I am using the hitch for a Snowsport HD plow on a j2019 Honda Ridgeline. The minimum height required for the plow is 8”. The height at the angling interceptor is just above 8 “ and 10” at the bottom of the push bar. Will use the plow tomorrow to see how it works and if any adjustments are necessary. If there is a height issue I will use a receiver extension 2” drop/rise if necessary. I have about 2000 ft of drive/ road to plow and this plow should do the job.
I’m very happy with the fit and finish of this hitch.
Just installed today with my brothers help. Great instructions/ photos. Did take about 2 hours start to finish, not the 1 hour suggested. Otherwise no issues.
Fair pricing and GREAT SERVICE. In the period of who has the lowest price, to me, service and product knowledge should be winning more business. I will spend more for the service levels companies like etrailer provide.
This is my 10th purchase of hitches for me, my family and friends. I will buy more!
excellent seller.. thank you
Fast shipping very helpful
Do you have a question about this Front Receiver Hitch?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Richard M.
7/9/2020
Great, no problems!