Summer Starts Here - Save up to 70%
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Perfect for light-duty towing, this custom, vehicle trailer hitch receiver features fully welded, gloss powder coated steel construction. Drawbar sold separately.
Features:
Specs:
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
Average Customer Rating: 4.7 out of 5 stars (126 Customer Reviews)
Perfect for light-duty towing, this custom, vehicle trailer hitch receiver features fully welded, gloss powder coated steel construction. Drawbar sold separately.
Owned for 1 year. Was a bit of a pain to install. Save yourself some time and just remove the rear exhaust pipes before the install. Works great for holding my bike rack.
Good directions. Seems like a good hitch except the holes were 1/2 inch off (too close) between the two sides. I was able to bend the frame slightly using a hydraulic jack and after that everything went together as the directions described. I had to use the access hole for the rearmost bolts rather than the pre drilled holes in the frame but that should be fine.
The box came with the hitch having torn through on both ends ( see picture). The frame was barely scratched so it wasn't a big problem but the packaging should have been better.
Relatively easy to install as a DIYer, works well to hold my ski and bike racks. I appreciated the installation videos on the website.
I gave a three star because the hitch did not properly fit my vehicle even though I provided the make, model and year. I had to make numerous modifications for it to fit on my vehicle. Before making those modifications I contacted you all to resolve the issues so that I could get a hitch that actually fit. One representative said they had the order pulled up and that they would get back with me and they did not. The second time I called they said the order did not exist. But I really wanted to get the hitch on my vehicle so I went to work on trying to figure out what I could do to make it work. I've been using it for quite a while so it seems to be working just fine now.
Excellent product, very fast in delivering. Ordered from them in the past and I will order again if I need another hitch.
This is on a 2018 Mazda 3 hatchback. I give it 5 stars. And One can get it installed alone. Just one little thing, it was a bit tight. I had to "stretch" one side to line up the bolts. to do this I installed one side loosely and then got one the other side and pulled and shook until the bolts dropped through the holes. Also, as you can see in a couple of pictures you will need to relocate at wire during install. I popped in out, stowed it and then clipped in back in.
The hitch receiver is great quality and looks good in my mazda 3 2018 hashback. Installation instruction was clear and easy to fallow it cleary indicates you need two people for easy installation, but unfortunately I did not have anyone available, so I ended up doing the installation by myself and still was moderate job (60 minutes). A little delay with shipping which is not etrailer fault, but their customer service was great and helped me duringbthe process until finally received my order. Overall good quality part and great service.
Shipping was prompt. Despite very little apparent damage to the box, the hitch had a few deep scratches and chips. I repaired these with black touch-up paint, but it shouldn't arrive like this. It would be nice if the mounting hardware (bolts and flat brackets) were stainless steel. Installation certainly requires the removal of the four rubber exhaust hangers. Use a jack stand under the main pipe to lower the muffler about two inches. The installation will be very difficult if attempted alone because the hitch has to be carefully moved into position and then the bolts to which guide wires are affixed have to be threaded through the holes on the brackets of the hitch.
The fit is good on a 2017 Mazda3 hatchback. Equal clearance all around and no interference with the exhaust pipes or bumper. Appearance wise, I think the Curt looks better than the Drawtite which a friend of mine has on his Mazda3.
I was just recently able to attempt installing my new equipment, but unfortunately it does not fit my vehicle.
I have a 2014 Mazda3 Hatchback, which this item is listed as fitting, but as you can see in the pictures the bolt holes are much farther apart on the equipment than on the vehicle.
It appears to have the correct product number which I ordered except that this item us not designed with a C as listed online.
Please advise on how to rectify the issue.
Instructions were good, install was easy, required no drilling or cutting for my application; 2104 Mazda 3 hatchback.
Removing the exhaust hangers was easy using a spray solution of water and dish soap, I used a cambuckle type of tie down hooked to the suspension to raise and lower the exhaust as needed. I unclipped a wire on the driver side frame to give a little extra space to position the hitch.
It helps to have a helper to position the hitch and hold it up while bolting it.
This is my second hitch from Etrailer and like the first one it arrived in good condition.
My search for a hitch led me right to etrailer, and the selection and ordering process was a breeze. Shipping was very prompt and the installation process was relatively straightforward. The online video was helpful, but I own the hatchback model so there are a few differences I had to figure out. Some basic bicycle lubricant helped to free the muffler mounts so I could access the mounting points. The only thing I was not able to do on my own was touque the bolts due to the tight clearance of laying under my car, which was expected. The hitch preformed well with the bike carrier I own and I hardly notice the hitch with out the rack on board. Definitely a quality product at a great price and I would certainly recommend etrailer.
So far so good. Install on my Mazda 3 hatchback was easier with my dad. Look up “how to remove rubber isolators” to make sure you have the hardware at home. Everything else came with the kit. You’ve got to be careful with the bolts or you’ll lose them inside your frame.
I haven’t towed yet for two reasons:
1. 1-1/4” receiver size isn’t the most common, so I’m ordering a fitting part from etrailer.
2. This product doesn’t include a wiring kit (some others do).
I don’t get under my car often, so it was kind of a fun job. Aligning the hitch to the car’s frame was a challenge. Easier with 2 people.
The C11377 did not align properly with the frame holes on my 2015 Mazda3 iSport 4dr sedan and had to use the back feeder hole. Also had to trim some of the bottom spolier but not visible from the back. Also was one who pushed a screw back into the frame. Wish they would account for that and include 5 screws.
The fit on my 2018 Mazda 3 hatchback was a touch off. I got one side loosely fastened and the other side, bolt holes were 1/8 or so off. I had to pry it a bit into place. Other than that it’s working fine.
Kelly
7/18/2023
The hitch after a year is holding up as expected. No issues at all.
Great service good product this is my third hitch
Not too difficult to install, instructions were clear and had helpful pictures. No Drilling or cutting, just dropped the exhaust (only held on by rubber grommets) and it bolted right in. I only used it for a tow hitch mounted bike rack and it was more can enough to hold 4 bikes. It seems like it would be very capable of hauling small trailers from uhaul or the trailers that hold canoe's or kayaks. Your major limitation is going to be the 1.25" opening, and your Mazda's engine power. The tow hitch is rock solid and I would recommend this to anyone looking to make their 2104+ Mazda3 more utilitarian.
Evan
1/30/2018
I sold the car I installed in on - but last time I saw it, it was still working great!
This was a perfect fit for my 2018 Mazda 3 Hatchback. At first it looked like I could get it in by jacking up the rear. Alas, not the case. However, raising the rear DOES make it easier to work on. If you can sneak a little screwdriver into the rubber muffler mount, and spray in some silicone or other lube, it makes the job of removing the mounts much easier. You only need to remove the BOTTOM part of the mount, by the way. The welds and powder coat finish look great...pleased with the product and looking forward to many miles pulling a small trailer with light boats or a motorcycle. Follow through with etrailer was very professional after they could not find the used hitch that I first ordered. Helpful and friendly....
James
8/10/2019
Pleased with the product...lots of use and still pleased with the design and function.
Very easy to install. It took me about 1hr. Looks nice too! Thanks Curt MFG!!!
Kevin A.
12/11/2013
Is this approved by Mazda? My dealership told me that a hitch would not be possible for my 2014 Mazda 3i Hatchback. I need one for a bike rack.
I put one on my Mazda 3 hatchback and it was as simple as could be. No drilling or anything like that. Fish the bolts thru the frame and tighten it down, then plug in the wires and hide them by the spare tire. The nice thing about this setup is that the plug is always inside and out of the elements when not in use. Even someone with very limited mechanical skills should be able to install a hitch like the one I have. Videos helped too.
Jon C.
3/12/2018
Still working great!
Good product, fantastic price! My only gripe, and it's a small one. I wish etrailer would have wrapped the hitch to prevent damage during transport. There are several spots where the powder coating is chipped off and living in the northeast this will just expedite the rust from setting in.
Mike
3/21/2017
After owning the hitch for a year, I couldnt be happier with the hitch. Having a hitch mounted bike rack is a much better solution than a roof rack. Amazing hitch for the money!
So happy I bought this hitch. The service was great, etrailer directed me to the right hitch for my car. My mechanic who put my hitch on really likes their products.
Tiana
1/30/2018
I love my hitch it removes the hassel of taking our families bike to the bike path so we find ourselves riding more...more bike riding more fun..thanks
The hitch it's easy to install, very well built, and if you follow up instructions it won't take longer than 45min to 1hr.
Really recommend this style hitch for Mazda 3
Marcin W.
4/15/2021
Hitch is a heavy duty build, perfect for bike, platform or small teargear trailer. Very happy with my hitch.
The curt trailer looks very beaten up and worn down. As if someone had it for years. Sadly, can't return it due to myself moving soon and I wouldn't want them to resell something I traveled with over 2,000 miles. While it works it is NOT in new condition.
Great product, probably the 3rd hitch I have bought from entailed. Everything it's been shipped fast with no issues. Took about 30-40 min to install. Great product and company.
We now have 3 Curt manufacturing trailer hitches in our family on various years of Mazda3. They all fit perfectly and were easy to install for this middle-aged woman. I also bought harnesses from etrailer. They have excellent service and an excellent website from which to order. I have installed both the wire-in harness and the plug in; I would recommend the plug in one for occasional towing. I was able to install the wire-in harness after some YouTube learning about using a multimeter. I also learned how to temporarily lower the muffler to install the hitch. A different brand of hitch is available that can be installed around the muffler instead of having to lower it, but I wanted a Curt Manufacturing hitch, so after some more You Tube learning I installed it without problems. I would definitely order from e trailer again!
Do you have a question about this Trailer Hitch?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Mike L.
1/30/2019
There is another hole in the frame member on the other side of the exhaust mount shown in your photo. The hole could be covered with a plastic plug, tape or undercoating, you might need to take a putty knife to the underside of the frame member to scrape away any undercoat or grime that might be covering the mounting hole.