Summer Starts Here - Save up to 70%
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
In-stock alternatives that can ship today
Designed for use with wide, off-road tires, this setup gives you more clearance and a smooth ride. Built-in shock absorption limits rattle and bottoming out. E-Z Lube, long, standard-height spindle maintains deck height. Fits any trailer frame width.
Features:
Specs:
Note: This Axle-Less system requires crossbeam support. If your trailer frame doesn't have a crossmember in place, you can retrofit it with one, or you can add a support by running a piece of 2" x 2" steel tubing through the square holes cut into these units. You could also add a steel reinforcement bracket to the inside of the trailer frame.
Get more ground clearance and a more comfortable ride when you're towing with Timbren's Axle-Less trailer suspension. This suspension system provides great shock absorption to comfortably get you where you need to go and to protect your precious cargo as you travel - even on rough terrain. With 2 independently operating units, you'll get better handling when making tight turns. And because this system eliminates your axle and has standard-height spindles built in, you'll get more clearance without having to raise your deck height.
There are many suspension options for your trailer or camper. So, what makes Timbren Axle-Less different?
Axle-Less systems are a definitive upgrade over traditional leaf springs, in part because they allow you to do away with your thru-axle, allowing for maximum clearance. As you've probably noticed, having a leaf spring suspension means that your axle will always hang at least a few inches below your trailer's frame, resulting in limited ground clearance. This may make it difficult to navigate off-road terrain.
In addition, while leaf springs do a great job of supporting an even load, they may cause your trailer to bounce and rattle when it's empty or to bottom out with a heavy load. And they don't offer any type of shock absorption for a smooth ride - unless you have upgrades built in. With Timbren's Axle-Less system, gone are the days of dealing with these annoyances - this suspension is designed for a quiet, balanced ride, whether your trailer's fully loaded or empty.
A torsion axle is a step up in terms of shock absorption, and it provides more clearance than a traditional, leaf spring suspension, but that crossbeam will still hang down some. And if your torsion axle gets damaged in any way, it can't be repaired - you'll have to replace the entire thing with a setup that matches your exact trailer frame width.
With the Axle-Less system from Timbren, you won't have a low-hanging axle beam to get in the way when you want to go off-road. The standard-height spindles on this setup will keep your deck height the same, so you'll get that extra clearance and still be able to easily load and unload your trailer. And the rubber springs and independent operation both combine to absorb shock and deliver a smooth, easy ride. In addition, the Axle-Less system can be easily maintained over time, and it will fit any trailer frame width, so you don't have to worry about potentially ordering the wrong size like you might with other systems.
Another suspension upgrade on the market is Timbren's Silent Ride. This setup is a great option to reduce bounce and rattle because it has the same AEON rubber springs as the Axle-Less system. But the Silent Ride still requires an axle, so you won't get the same ground clearance or low deck height as you will with the Axle-Less suspension.
The Timbren Axle-Less suspension is designed with you in mind. All of the parts work together so you can tow your trailer comfortably - regardless of load size.
The first step in installing the Timbren Axle-Less suspension is to make sure that the mounting points for each unit are directly across from each other. The easiest way to measure this is to mark the desired mounting points on your trailer's frame. Then measure the distance between these points and the center of your trailer coupler. These measurements (A and B) need to be within 1/8" to keep your trailer frame square.
Once you have your mounting points lined up, you'll be ready to install the system. Drill 3 holes into your trailer frame at the desired mounting points. Then bolt each unit to the frame with Grade 8, 1/2" bolts (not included).
Because Timbren's Axle-Less system eliminates your trailer's thru-axle, you'll have to find another way to get the crossbeam support that keeps your trailer frame square. You have a few different options to do this depending on your application and how much fabricating you're comfortable doing.
If you're building a trailer, the best option is to begin building with the Timbren Axle-Less in mind and include a crossmember where you want to install the units on your frame. You can also retrofit an existing trailer with a crossmember.
If you don't have a crossmember where you want to install the Axle-Less system (and you don't want to add one), pick up a section of 2" x 2" steel tubing from a nearby weld shop. This tubing will serve as a support to keep your trailer square. It will hang only about an inch down from your trailer frame, providing more clearance than a thru-axle.
After you've mounted both of the units to your frame, you'll need to drill 3 holes into the steel tubing and into the built-in, square holes. Then, insert the tubing through the holes and secure it with 3 bolts (not included) on each side.
The last option is to fabricate a reinforcement bracket that can be attached to the inside of your trailer frame and to the Axle-Less suspension. It may be a little harder to fabricate a compatible bracket than to mount steel tubing, but you may get additional clearance with this method.
The following diagrams show measurements taken on the Timbren Axle-Less suspension system.
| A | B | C | D | E | F |
|---|---|---|---|---|---|
| 13" | 19" | 1" | 5" | 5-15/16" | 4-1/4" |
| G | H | I | J | K | L |
|---|---|---|---|---|---|
| 5-5/8" | 8-1/2" | 4-3/4" | 1-3/4" | 3-3/8" | 3-11/16" |
Alternate Instructions
Average Customer Rating: 4.6 out of 5 stars (302 Customer Reviews)
Designed for use with wide, off-road tires, this setup gives you more clearance and a smooth ride. Built-in shock absorption limits rattle and bottoming out. E-Z Lube, long, standard-height spindle maintains deck height. Fits any trailer frame width.The service from etrailer has been great! They have been very helpful through the entire purchasing process. My one star is due to the quality of the product. First, for something as heavy duty as these are, you’d expect better packaging. On arrival, one of the spindles was sticking out of the box and the hand holds were torn on one of the other boxes. I was a little worried what I might find in the damaged box but everything seems to be intact. The disappointing part is the quality of the welds. For the price you are spending on these, I would expect a higher quality of fabrication. There is undercut in the welds that hold the three support plates together and big ol sloppy welds every where else. Unsure of what to do as my trailer has been designed around this suspension system.
The customer service has been excellent with Etrailer!!! I got to work with Anna and she did a great job on my order. The product seems to be great, just as Timbren stated. It went together very well on the trailer that I'm building. I can't wait to finish this project and be rolling into the backcountry and staying for a few days.
I found etrailer.com looking for these. A very knowledgeable gentleman helped me select the proper self-adjusting brakes and drums for the axles I bought.
Well this is the 6th time that you have left out a part of the suspension we order. Luckily you've fixed the situation and have told me you'd ship out replacements. But I shouldn't have to worry about getting partial shipments from you. Its an unneeded headache
Have not installed yet. Product arrived well packaged and undamaged. Appears to be very heavy duty and well built. The reason I'm only giving 4 stars is the finish on the spindle seal surface leaves much to be desired. As it is, I don't think it would take long for the seal to fail. It's nothing that a fine file and 600 grit sand paper won't take care of which I will do. It just irks me when I have to rework careless workmanship. Especially when I'm spending $[XX]. Will update after I do my installation.
What a great product! Highly recommend buying from this company.
Hands down the best costumer service in my life of retail. Excellent packing and product!
Thank you
Greg
The axle-less suspension worked very well for my boat trailer. The suspension was easy to attach to the trailer frame and provided a lower profile than the traditional leaf spring and axle system.
I purchased the 3500 lb. set w/4" drop. Wish they made a 2" drop. Install was fairly easy, but most of your time will be consumed with alignment measurements, acquiring shims, and making adjustments. I was lucky to have a very square trailer frame. However, the "slop" in the all of the mounting bolts (especially, the spindle mounts) is more than the 1/8" window they specify. You will want to preload all bolts before tightening, and then measure for alignment/toe-in. The units are supposed to have camber built-in, but it's not near enough (more shims). Also, this suspension has more travel then the documents indicated. I had to re-mount my fenders 1" higher to keep the tires front hitting. When fully loaded, you might have 1" of travel left. All that being said, the ride is better than I anticipated. It's less bouncy than a torsion axle, and very quiet. If I was building a trailer from scratch, I would use this system, again.
It is important to know that your wheels are going to sit very tight to the trailer frame. I needed to add an extension to the hub for it to clear the sides of the camper I built.
We made an amazing creation out of those two axle-less axles.
We made a large fuel cell that is used for offroad use and it has worked excellent this entire time.
They are really great products and we would love to work with them again.
Actually, we do a ton of social media stuff and youtube and if you ever have interest in sending us products to build content around, I would love to have the opportunity!
Thanks,
Michael Brandt
Garage Bound, LLC (On Youtube and Instagram and all the other socials)
The trailer rides great down the road and no more worries about saltwater and rusty leaf springs. Not a cheap option but I’m very happy with the setup. When installing, just be sure to measure accurately and have sharp drill bits. A drill press type of guide also helps ensure correct drilling angles. The first picture is of a mounting gusset a local welding shop made. One is needed for each side and necessary to provide needed mounting strength-at least on my trailer frame. Pics 2 and 3 show the mounted suspension on one side of the trailer. Pic 4 shows the suspension on one side of the trailer with the axle attached and a separately purchased disc brake assembly mounted on it. Finally, pic 5 shows a 2” box channel between both suspension assemblies. Independent suspensions would have been nice, but I wanted to ensure trailer rigidity was maintained. So, after one year, so far, so good. It’s all smooth sailing down the highway.
Very smooth pull. I'm very impressed on how the trailer pulls. My traditional axle trailer seemed to bounce a lot on the highway which made a lot of noise, but with the Timbren Axle-less that I installed on a new trailer, the trailer is so smooth and way less noise.
Great product.
Purchased 2 sets of the Timbren 1200 Axle-less systems for upgrading the suspension on an older 30' ft glider trailer. Single axle with small (13") tires made towing tough due to porpoising, dragging on drive entrances do to poor flotation; also German made and metric, no repair parts. GVW 2000 lbs equated to bouncy ride.
Dual sets now allow the trailer to ride over bumps and sharp inclines easily, smoothly, little bounce on country roads; porpoising is history. My glider now rides securely, safely, quietly.
Install time 4 1/2 hours (includes head-scratching). Results are outstanding, units are totally solid. Recommend the square tube interconnect, easy and quick - trailer frame was on the light side, so a precautionary fix. Clean look underneath.
Ordered 5 wheels w/tires, very nice.
Helpful neighbor so impressed he ordered a HD single set for his new DIY snowmobile trailer.
Customer satisfaction 100%, from phone order, online support, product information, immediate shipping, install instructions, followup... HIGHLY RECOMMENDED!
I used these axles in a different way than most would. I needed a trailer that was small, could handle tight switch-backs, carry 600 lbs and be light. I had this idea and as a retired design engineer I saw a great possibility in this axle. I have made four of these trailers now, one as a camp trailer, 2 for trail work for State Parks and one as a utility trailer.
Installed the Timbren Axle-less suspension a little over a year ago and approximately 5000 miles ago. I have been extremely satisfied with the installation and performance thus far and have had no issues. I also chose to install an optional crossmember for more strength using a 1/4" thick piece of 2x3 steel. I had to increase the weight capacity of my campers suspension due to renovating the interior completely and adding more weight. I also strengthened the frame to accommodate the extra weight. In addition to installing the Timbren 5200LB system I installed new 12" electric brakes and upgraded to 225/75R15 tires with E load range rating.
Trailer suspension and disk brake performance is outstanding big big difference over leaf spring and electric drum brakes.
Installation required modifications to the frame to monut the timbren suspension
Installed the Timbren Axle-less suspension a little over a year ago and approximately 5000 miles ago. I have been extremely satisfied with the installation and performance thus far and have had no issues. I also chose to install an optional crossmember for more strength using a 1/4" thick piece of 2x3 steel. I had to increase the weight capacity of my campers suspension due to renovating the interior completely and adding more weight. I also strengthened the frame to accommodate the extra weight. In addition to installing the Timbren 5200LB system I installed new 12" electric brakes and upgraded to 225/75R15 tires with E load range rating.
I rebuilt a 4 x 8 trailer using the Timbren Axle-Less Trailer Leaf Spring Suspension and it works great. I would recommend it to others.
Incredible system. Handled our Overland trek through Colorado and Moab. These axles on our 1917 Ford bed ran multiple Jeep Badge of Honor trails. The suspension handled flawlessly. Handles off camber rocks and drop offs smoothly. We ran the 4 inch lift and off road offset to fit the factory Jeep wheels.
They have more pros than cons, but the second set I bought broke the flat plate that holds the spindle at about 8 months. The steel quality seemed less than I would expect since it basically peeled it back like a pop can as you can see in the pictures. Otherwise I like the clearance and ride. They last 2-3 years where the torsion axles I replaced would wear out in 4 months after driving down rough gravel roads. There is a grade zerk on the underside which I didn't realize until I bought the second set. That would have helped the first set last longer had I known about it.
Do you have a question about this Trailer Axle?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Katrina D.
1/10/2024
I am sorry to hear that you received them in this condition. Lets get your information over to customer service so they can get these exchanged.