What is Needed to Convert Oil Bath Hub to Grease and Also Pick Out Replacement Spindle

Question

Question:

my oil bath system and spindles are shot and I wanna go to a old school grease setup. I dont want the expensive spindles with the grease passage way to the inner bearing. can you help me to get a regular spindle and a bearing and grease seal setup? thank you

asked by: Pete

0

Expert Reply:

In general you don't have to do anything to your current setup to convert it to grease aside from just remove all of the oil and replace it with grease. The oil seals will work just fine with grease instead so all you need is hub grease like the LMX Red part # L11390 and you'd be set.

Since your spindles are shot though I will need to know more info to pick out the correct replacements. Use a digital caliper like the part # PTW80157 to measure the spindle you have where the bearings and seal ride and let me know what you find. Or you can check out the link I attached to see all of the spindles we offer and there's a chart at the top that you can use to identify what you have and get correct replacement.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 3

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 4

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 7

Assuming your tires are in good shape without any bulges the easiest way to determine if you have a bent spindle is to take a straight edge that is longer than the tire and lay it across the tire parallel with your trailer frame and then measure the…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 10

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 11

I am sorry I don't have any tires that are going to fit your rim. I do have a couple of comparable size tires that come in a wheel tire combo. I have listed the two below along with their lug patterns. 5 on 4-1/2 Lug Pattern - Kenda 205/65-10…

view full answer...

Answer 12

To determine if there are compatible hubs and associated bearings to replace your current hubs to a more standard size you will have to take several precise measurements on the spindle of your axle. It is recommended to use a set of dial calipers to…

view full answer...