Timbren Wide Tire Axle Less System that Fits Dexter Hub Kits K71-510-00 and K71-511-00 10

Question

Question:

Hi: Can you help me? please I have a 4x4 trailer and I need to change the suspension... I already have electric brakes : + K71-510-00 Left Hand 10inch Electric Brake Kit includes hub/drum + K71-511-00 Right Hand 10inch Electric Brake Kit includes hub/drum I would like to know if ASR1THDS02 is compatible with this brakes/Hub/Drum?

asked by: Roy

0

Expert Reply:

The hub you have is basically the part # 84546UC3-EZ which means that for a Timbren axle less system that would work with them you would need the part # ASR2KHDS02 that has the brake mounting flanges that match the assemblies you have and a spindle that will fit the hub.

expert reply by: Jameson C

0

Answer 1

The only axle we have that will allow for your same measurements with a 5 on 4-1/2" bolt pattern in the Timbren Heavy-Duty Axle-Less Trailer Suspension #ASR2KHDS02. This will pair with 2 of the Dexter Trailer Idler Hubs #84545UC1-EZ to give…

view full answer...

Answer 2

The difference between the Timbren Axle-Less System Regular Tire and the Timbren Axle-Less System Wide Tire will be the distance between the hub face and the trailer frame. I have attached a diagram and chart that will give you the dimension for…

view full answer...

Answer 3

That's a good question, and it wouldn't be just the spindle itself that gets replaced on the Timbren Axle-Less systems, it would be the whole spindle arm that would need to be replaced if there was any damage. If you take a look at…

view full answer...

Answer 4

I have another option for you, but at this time we do not offer a hub with the 5 on 5" bolt pattern that is rated for 17" wheels. For example the Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 5 - Pre-Greased #84550BX you were looking…

view full answer...

Answer 5

I have a solution for you, and it sounds like you're looking for a Timbren system that can be used with 5 on 5 hubs that would allow you to use Jeep wheels. Unfortunately the Timbren #ASR1200S03 spindle does not have any hubs with that bolt…

view full answer...

Answer 6

The Kenda Karrier ST145/R12 Radial Trailer Tire with 12" Black Mod Wheel #AM35354 will be about 1/2 an inch shorter than your current 5.30-12 tire so it that regard it would work perfectly fine. Now the included wheel is designed to attach to a…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...