Grommet for ST33 Series Tall Rectangle Flush Mount Trailer Lights

See what our Experts say about this Optronics Accessories and Parts

• Can Optronics LED Backup Light # BUL35CB Be Mounted Horizontally
  The Optronics Flush Mount LED Backup Light you referenced, part # BUL35CB can indeed be mounted onto the deck of a car trailer. The lamp is sealed, so you will have no worries about water entering the lamp housing. You would also need a grommet, part # A33GB and the wiring pigtail, part # A45CB.
  view full answer...
• Are Load Resistors Needed for Reverse LED Trailer Lights
  You will not need load resistors to install the Optronics LED Backup Light for Truck or Trailer # BUL35CB; load resistors are not needed for reverse lights like these. The only thing you will need are Grommet # A33GB and a 2-wire pigtail, either part # A45CB or the right-angle pigtail, part # A49PB. I have added links for video reviews for you to check out as well.
  view full answer...
• Depth Dimension of Optronics Miro-Flex LED Trailer Stop/Turn/Tail Light STL35RB
  The actual depth of the Optronics Miro-Flex LED Trailer Stop/Turn/Tail Light # STL35RB is 2-5/16-inches, as shown in the linked diagram which includes overall dimensions too, but you will also need to allow for the right-angle plug # A47PB which will add another inch. This light is intended for installation using rubber grommet # A33GB.
  view full answer...
  
• Amber Trailer Blinker/Running Light Recommendation for Use on an Older Truck
  We don't have exactly what you said you need, but the closest thing we have would be the Miro-Flex, Waterproof, Rectangular, LED # STL35AB. This is an LED amber light you could use that has dual intensity so that it can be used for a blinker and running lights. Only thing is that this is much bigger at 5-5/16" L x 3-7/16" W x 2-5/16 D. For a harness to plug into the light you would want # A47PB and then for a grommet part # A33GB.
  view full answer...
  
• Running Lamp Circuit on Thule TH665C Transporter Combi Cargo Carrier Not Working
  The taillights on the Thule # TH665C Transporter Cargo Carrier should function as brake lamps. turn signals and running lamps. It sounds like you have a problem with the running lamp circuit, as the license plate lamp is on the same circuit. I'd first test the trailer connector on the vehicle while the headlights are on. A simple circuit tester like # PTW2993 works well for this. Check the pin on the connector that's fed by the brown wire. If you're not getting power on that wire with...
  view full answer...
• Recommendations for installing a LED Trailer Light # STL35RB on a 2002 Ranger Trail Trailer
  This Miro-Flex, Waterproof, Rectangular, LED Trailer Stop/Turn/Tail Light # STL35RB that you referenced should work well with your trailer wiring. You will need a Straight 3-Wire Pigtail # A45PB to wire it into your trailer wiring. The red wire from this harness will run to the turn signal circuit, the black is the tail signal, and the white will ground to the trailer frame on a clean metal surface to complete the circuit. You might also be interested in purchasing a Grommet for ST33...
  view full answer...
• LED Trailer Tail Light Recommendations for a Boat Trailer
  The Sealed, Miro-Flex, Thin Line, LED Lights, # MCL63CRB, are DOT approved as Trailer Marker, Clearance or ID Lights only, so you would not be able to use them as tail lights. A similar light in shape and size that would work for you is the Miro-Flex, Waterproof, Rectangular, LED Trailer Light, # STL33RB. You would also need a wiring harness like # A45PB, and a grommet, # A33GB. Or, if a rounded light is acceptable, you can go with # STL70RB, with wiring # A45PB and Grommet # a70gb.
  view full answer...
• Grommet and Pigtail Needed for the Optronics Miro-Flex # STL35RB Trailer Light
  The grommet that you will want to use to install the Optronics Miro-Flex # STL35RB is the Optronics part # A33GB. For a pigtail you have 2 different options. The 3-Wire Pigtail for Optronics Trailer Lights part # A45PB has a straight connector and the Right Angle 3-Wire Pigtail for Optronics Trailer Lights part # A47PB has a right angled connector.
  view full answer...
• Can the Miro-Flex LED Trailer Light be Mounted Vertically and Horizontally
  As long as you have adequate room to mount the Miro-Flex, Waterproof, Rectangular, LED Trailer Stop/Turn/Tail Light # STL35RB you could mount it in basically any orientation you like. You might also be interested in purchasing a Right Angle 3-Wire Pigtail # A47PB or a Straight 3-Wire Pigtail # A45PB depending on your mounting location. Or a Grommet # A33GB for mounting.
  view full answer...
• Can the RV Porch and Utility Light be Used on a Camper Shell for Side Illumination for Sled Dogs
  The RV Porch and Utility Light, # RVPL3C, would definitely be able to handle normal highway speeds, if mounted correctly, but a car wash might be a different story. These lights were designed for RVs and they are not normally ran through car washes. If the car wash were a touch-less model then you should be fine, but a car wash with the mops that twirl would most likely cause an issue with the lights protruding from the side of the shell. Another option may be to install a flush mounted...
  view full answer...
• Is LED Backup Light BUL35CB Much Brighter Than Incandescent BU33CRXLB
  The difference between the lights isn't in the brightness so much as the clarity, so the Optronics LED Backup Light for Truck or Trailer # BUL35CB is not significantly brighter overall than the Backup Light with Red Reflex Reflector # BU33CRXLB. I have added some photos showing the lights on for some reference, though keep in mind it's not a perfect representation due to camera angle, room darkness, etc. but I wanted to show an example of the different kind of light. In regards to the...
  view full answer...
  
• Availability of White LED-Type Rectangular Backup Light
  For a rectangular white LED-type backup light I suggest the Optronics Flush Mount LED Backup Light # BUL35CB. This recessed-mount light uses an industry-standard plug like # A45CB and a mounting grommet # A33GB. Please click on the video link for more.
  view full answer...
• Dimensions and Mounting Grommet Recommendation for the LED Back Up Light part # BUL35CB
  I attached a picture of the LED Back Up Light part # BUL35CB that shows its dimensions. If you were planning on making a grommet to install these lights you could instead just get the Grommet part # A33GB as this grommet is specifically designed to fit this light.
  view full answer...
  
• Available Flush Mounted Tail Lights for Camper
  We have many flush mount taillights to choose from. If you click on the provided link, you can see our selection. We have a few lamps that are similar in size to the Wesbar lamp you mentioned. The Optronics Flush Mount Rectangular Tail Light, part # ST33RB measures 5-5/16 by 3-7/16 inches. It uses a grommet mount, sold separately as part # A33GB and would require a pigtail, part # A45PB. The same lamp is available in a LED version, part # STL33RB which would use the same grommet and pigtail. Optronics...
  view full answer...
• What Size Hole Is Needed to Install the Flush Mount Rectangle Light and Grommet
  The Rectangle LED Trailer Stop, Turn and Tail Light, # STL34RB, needs a hole that is 3-3/4 inches by 5-3/8 inches. This light comes with the grommet and the 3 wire pigtail for installation. There is also a right angle pigtail available, # A47PB, if space is limited behind the mounting location for the light. For a really clean looking installation you will want to radius the corners to match the corners of the grommet. I would draw a 3-3/4 x5-3/8 inch square on a piece of paper or cardboard...
  view full answer...
• Can Custer 4-LED Strobe Light or Running Light Be Used As A Back Up Light On 2001 28 ft class C RV
  I would encourage installing a light that is intended to be a backup light on your motorhome. You may want to check out part # BUL35CB. This is a 16-diode LED light that is certified as a back-up light when installed as a pair. This light also requires a grommet, part # A33GB, and a 2-wire pigtail, part # A45CB. The Custer 4-LED Strobe Light or Running Light, part # STRL4A is actually designed to be a running light or a strobe light. You could attach it to the reverse light circuit on...
  view full answer...
• Will Right Angle Pigtail Fit With STL33RB Optronics LED Trailer Tail Light
  Yes, the Optronics LED Trailer Tail Light # STL33RB will pair up directly to the Right Angle 3-Wire Pigtail # A47PB. To complete your install you may also want to pick up the Grommet # A33GB and Butt Connectors # DW05743-5. Attached are some videos for you to check out.
  view full answer...
• Is there a Mounting Bracket for Trailer Back Up Light # BU33CB
  There is no bracket for external mounting of grommet # A33GB so you will have to cut a hole where you want the grommet and light to go. Use the grommet as a template to cut the hole. Start small because you can always work your way up to a larger hole if needed.
  view full answer...
• Recommended Parts to Install Optronics Flush-Mount Clear LED Trailer Backup Light # BUL35CB
  The Optronics Flush-Mount Clear LED Trailer Backup Light # BUL35CB that you referenced uses a tiny amount of power since it features high-efficiency LEDs instead of standard incandescent bulbs. Its power draw is about 1/10th that of standard bulbs, approximately 0.295-amps at 12.8 volts. This light uses a standard 2-prong connector that accepts wiring pigtail # A45CB. It mounts with grommet # A33GB. To use this as a backup light you will need to connect it to your Wrangler's reverse light...
  view full answer...
• What are the Dimensions of Optronics Flush Mount LED Backup Light BUL35CB
  The LED backup light # BUL35CB is 5-5/16 inches long x 3-7/16 inches wide x 2-5/16 inches deep. You will also need a wiring pigtail, # A45CB to install this light. For a grommet, use # A33GB. I have included a picture showing the light dimensions for you.
  view full answer...
  
• What Size Hole is Needed to Mount the Optronics Tail Light # STL35RB
  With the Tail Light, # STL35RB, inside of the appropriate grommet, # A33GB, you would need a hole that is approximately 5-7/16 x 3-3/4 inches. You will also need the appropriate wiring harness, # A45PB.
  view full answer...
• What Size Hole is Needed to Mount the Optronics Tail Light # ST33RB
  With the Tail Light, # ST33RB, inside of the appropriate grommet, # A33GB, you would need a hole that is approximately 5-7/16 x 3-3/4 inches. You will also need the appropriate wiring harness, # A45PB.
  view full answer...
  

Do you have a question about this Accessories and Part?