Vehicle Heaters Specs:
Features:
This cartridge heater clips into the cavity of your engine block and submerges in the coolant to keep engine fluids from thickening. Results in easier start-ups, faster heating of your cab, and less wear and tear on your vehicle in cold weather.
Installation Notes:
OEM factory heater is thermostatically controlled; this product has a thermostat while part KH11810 is a cartridge heater without a thermostat
More Information >Vehicle Heaters Specs:
Features:
Simply push a button in your cab to inject ether fuel (not included) into your intake manifold and get fast, reliable startups in cold weather. Connects to battery - no need to plug anything in. Thermostat ensures fluid is only dispensed when needed.
More Information >Vehicle Heaters Specs:
Features:
Simply push a button in your cab to inject ether fuel (not included) into your intake manifold and get fast, reliable startups in cold weather. Connects to battery - no need to plug anything in. Thermostat ensures fluid is only dispensed when needed.
More Information >Vehicle Heaters Specs:
Features:
This frost-plug heater replaces the frost plug in your engine block and submerges in the coolant to keep engine fluids from thickening. Results in easier start-ups, faster heating of your cab, and less wear and tear on your vehicle in cold weather.
Installation Notes:
OEM factory heater is thermostatically controlled; this product has a thermostat while part KH11455 is a heater without a thermostat
More Information >Vehicle Heaters Specs:
Features:
Just turn your ignition to inject ether fuel (not included) into your intake manifold and get fast, reliable startups in cold weather. Connects to battery - no need to plug anything in. Thermostat ensures fluid is only dispensed when needed.
More Information >Vehicle Heaters Specs:
Features:
Simply pull a knob that installs in your cab to inject ether fuel (not included) into your intake manifold and get fast, reliable startups in cold weather. Manual design means you get to choose when fluid is dispensed, and no electricity is needed.
More Information >Vehicle Heaters Specs:
Features:
Just turn your ignition to inject ether fuel (not included) into your intake manifold and get fast, reliable startups in cold weather. Connects to battery - no need to plug anything in. Thermostat ensures fluid is only dispensed when needed.
More Information >Videos
for Vehicle Heaters
Help Articles
for Vehicle Heaters
Expert Answers
for Vehicle Heaters
The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.
view full answer...Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…
view full answer...By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles…
view full answer...I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for…
view full answer...On single axle trailers typically you put the hanger spacing right at 1/4 of an inch shorter than the leaf spring length from eye to eye center. So if you were using the leaf spring part #e54SR that you referenced which measures 25-1/8 inches long…
view full answer...Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and…
view full answer...The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…
view full answer...In order to install a brake controller on a dump truck you'd first need to start with a 4-way trailer connector and then adapt this to a 7-way so you can hook up a brake controller. I won't have much…
view full answer...We do have a compatible grease seal for your 168255TC oil seal, however, we do not carry rubber coated seals in this size. The 168255TC oil seal was designed to work with oil bath hubs on a 3,500 lb axle. For the most part, axle manufacturers have…
view full answer...To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…
view full answer...It sounds like when the Redarc Tow-Pro Elite Brake Controller #RED44FR was installed on your 2022 Toyota Highlander that they may have damaged the brake signal wire or tied into the wrong wire. I recommend taking it either back to the shop who…
view full answer...To replace your WFCO WF-8750P power center I recommend the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K. This 2-in-1 AC/DC distribution panel and converter charger keeps your power systems easily…
view full answer...Filter Products (14)
Contact and Help
What our customers are saying:
In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!
Randy
Watkinsville, GA