The shaft diameter of the Lippert Components Spare Tire Winch with Offset Cable # LC159056 is 1/2 inch. It's designed to be used with the intermediate shaft # LC1315411. view full answer...
PART IS NLA. QUESTION IS MOOT. DISPROVE POST.
HappiJac does offer camper tie downs that fit your 2006 Dodge Ram 2500 short bed but the part # LC182906 is not the tie downs you'd need. Instead you'd want the part # LC182908-182928 which is the correct kit that fits your truck. This also comes with a stabilizer bar that is designed to help distribute the camper load between the tie downs. If you didn't want the stabilizer bar you'd just need the # LC182908 instead. view full answer...
The TorkLift SuperHitch Magnum Trailer Hitch Receiver - Custom Fit - Class V - 2-1/2" # TLD1102-30 you were looking at is confirmed to fit the 2003 - 2012 Dodge Ram Pickup 2500 and 3500 - with factory hitch, 2010 - 2012 Ram 3500 Pickup with factory hitch, and 2010 - 2012 Ram 2500 with factory hitch. view full answer...
The Lippert # LC373965 install hardware kit for the # LC243621 flip-down tailgate storage system isn't vehicle specific. The hardware kit is designed to bolt or weld to the 2 inch wide frame extensions, as is shown in the provided photo.
If the frame extensions holding the rear bumper in place on your travel trailer are 2 inches wide and provide at least 4 inches of distance between the edge of the bumper closest to the travel trailer and the back of the travel trailer, the # LC373965... view full answer...
The Brophy Stake Pocket Mounted Camper Tie Downs # TDSF work with most full-size, non-dually pickup trucks with straight fenders and single-wall construction, model years up to and including 2010. I have included a couple diagrams you can take a look at that include measurements so you can verify they will work with your 2007 Dodge Ram SRW 3500, as well as a video that touches on installation. These will also work with truck bed campers with an overall length up to 8'.
You will also need... view full answer...
I checked with Malone and the Malone Hanger 3 Bike Rack part # MPG2139 is a fit for a 2014 Dodge Durango. In regards to the spoiler, if this is factory then there will not be any issues but if this is aftermarket then this bike rack would not work. view full answer...
They are not compatible, I verified with TorkLift there are different rear tie-downs for your 2003 Ram 3500 long bed for the factory hitch and the TorkLift SuperHitch Original Trailer Hitch Receiver # TLD1102.
The correct fit for your truck and the SuperHitch Original # TLD1102 are the TorkLift Custom Frame-Mounted Camper Tie-Downs # TLR3503. view full answer...
If the Yakima Control Towers were the ones designed for factory installed tracks part # Y8890027 then yes they can fit the RTC tracks # RTC14 with the # Y00221 as the landing pad set. view full answer...
For your 11.5L x 7.875W x 12H battery I recommend the TorkLift PowerArmor Locking Battery Box # TLA7712R. This This 24-15/16" x 9-3/4" x 13" box keeps batteries safe and secure. The heavy-gauge aluminum is lightweight and rustproof and the powder coated outer frame is durable for a long lifespan. It includes hold-down straps, locking lid, access hole for wiring, and hardware. The extra space will allow for proper ventilation and give you plenty of space to connect wiring for all your trailer's... view full answer...
As the Thule Archway was discontinued in 2019, I cannot say what it will and will not fit, unfortunately. However, this was a confirmed fit before 2019 and I included a video we did on a 2016 Durango. I can also say that the arms on the Archway are 10 1/2 inches apart, so if your bike frames are wider than that, you will not need any adapters, like the Swagman Deluxe Bike Frame Adapter Bar # 64005. view full answer...
I contacted Dexter and the Unitized Oil Seal for Trailer Hubs part # 10-63 do not require RTV sealant or a gasket maker. They are typically used in oil bath hubs. I have attached an installation video for your reference. view full answer...
The spare tire retainer would almost certainly interfere with installing the # 75210, but we do have a hitch that is positioned a bit differently so it would fit perfectly. The Curt # 13250 class III hitch will avoid the spare tire retainer, as shown in the provided photo. view full answer...
The Hopkins Plug-in Simple Brake Wiring Adapter, # HM47755, for your 2008 Dodge Ram will fit Hopkins Agility, Reliance, Impulse, and Brake Force brake controllers. I have included a link to the installation details for reference. view full answer...
We carry several floor mats for the second and third row seats of your 2012 Dodge Grand Caravan, but they will span the entire width of the floor. Choosing the correct floor mats for your van will depend on how it was equipped.
For models with the 2nd row bench seats without the Stow-N-Go option, we have 2nd row floor mats like part # WT440272, and 3rd row floor mats, # WT440273. These mats are also available in gray as part # WT460272 and # WT460273 and tan as part # WT450273 and # WT450272.... view full answer...
The Putco Polished Stainless Locker Truck Bed Side Rail you mentioned, part # P99862 will indeed fit the 2012 Ram Laramie Big Horn Crew Cab with the 5-1/2 foot bed. It will fit models without the Ram Box.
For installation details, click the provided link. view full answer...
To install a Reese Elite Series fifth-wheel hitch and a gooseneck ball in your 2012 Dodge Ram 3500 Pickup, you will need the Under-Bed Rail and Installation Kit for Reese Elite Series 5th Wheel Trailer Hitches, # RP30158-52. This is the under bed kit that is equivalent to the Ford kit, # RP30126, that you mentioned and includes the gooseneck parts for the 2012 Dodge Ram 3500 with 6 or 8 foot bed.
This install kit is designed to work with the Reese M5 Series 27k hitch, # RP30922.
I attached... view full answer...
If your 2000 Dodge Ram 3500 has a factory mirror like the one pictured on the product page for Towing Mirror, # 10502, then the mirror will fit. But it will not fit sport mirrors or mirrors that are on a post. The driver side mirror is # 10501. I have included a link to a video review for reference. view full answer...
According to Pollak, the Replacement 7-Way Trailer Connector you mentioned, part # PK11893-11933 will fit the OEM connector on your 2001 Ram. The square connector will plug into the OEM connector located behind the rear bumper. The round connector will plug into the rear of he replacement 7-way. view full answer...
The best hitch for your 2006 Ram 3500 is going to be the Draw-Tite Hitch item # DT45518 you were looking at. This hitch is custom fit and bolts to your truck with included hardware.
This hitch was designed for the 8 foot bed model Ram trucks that have the factory hitch. It is the best option for getting as close to your bumper as possible.
The Draw-Tite item # DT45518 is a class V hitch with a 2-1/2 inch receiver opening. It has a Gross Trailer Weight rating of 12,000 lbs and a Tongue... view full answer...