Expert Answers about Dodge Caliber fit

Expert Answers about Dodge Caliber

Will Curt Class I 1-1/4 Inch Hitch # C11006 Fit a 2007 Dodge Caliber R/T AWD Model
I spoke with my contacts at both Draw-Tite and Curt, who both confirm that their Class I receiver hitches # 24769 and C11006 will fit the 2007 Dodge Caliber R/T AWD model as long as it is not an SRT-4 model. Although both hitches look very similar and have the same weight bearing capabilities, I would recommend the Curt model due to its additional mounting points. In my opinion, the two additional mounting locations would make for a stronger installation. I will provide links to the installation...
view full answer...

Block Heater for 2009 Dodge Caliber and Install Location
You can warm up the engine of your 2009 Dodge Caliber with the Kat's Heaters Custom Fit Engine Block Heater # KH11812, which is the correct fit. The location installation is in the front left, marked "FL" on the accompanying photo from the directions that I cut out for you. I've added a link to a video review for you to check out as well.
view full answer...

What Ball Mount For Draw-Tite Class I Trailer Hitch Receiver, # 24769, on 2007 Dodge Caliber
All Class I, 1-1/4 inch trailer hitches will require a special ball mount, and are designed for Class I accessories. The Class I 1-1/4 inch hitches will not accept any Class II 1-1/4 inch accessories. The Draw-Tite Sportframe Drawbar 5/8 inch Rise 2000# Kit, # 3591, is designed to be used in the Draw-Tite Class I Trailer Hitch Receiver, # 24769, on your 2007 Dodge Caliber. If a different ball mount is needed for towing a trailer then that means your vehicle most likely should not be towing...
view full answer...

Which Tow Bar Should Be Used with Roadmaster EZ Base Plates for 2010 Dodge Caliber
With Roadmaster base plates, like the EZ Base Plate Kit # 52281-1 that are confirmed to fit the 2010 Dodge Caliber excluding SRT-4, you will want to use a Roadmaster tow bar to ensure the base plates and tow bar are compatible. I recommend the Roadmaster Falcon Tow Bar, Motor Home Mount # RM-520. A motor home mount tow bar fits into the trailer hitch receiver on the motor home or tow vehicle and will store on the motor home when not in use. The quick-disconnect system on the Falcon tow...
view full answer...

Which Trailer Hitches Will Fit a 2008 Dodge Caliber R/T
The good news is we have a hitch that will fit a 2008 Dodge Caliber R/T. The Curt Trailer Hitch, # C11006. This is a Class I hitch, 1-1/4 receiver opening, 200 pounds tongue weight capacity, 2,000 pounds gross trailer weight. I have included a link to the installation instructions below. The Draw-Tite trailer hitch has some subtle differences in terms of where it mounts and how it is designed which is why it will not fit the R/T model.
view full answer...

Tire Chain Recommendation for a 2007 Dodge Caliber AWD with 25/50-18 Tires
You can use the Thule Standard Snow Tire Chains, # TH01221104, on 225/50-18 tires on your 2007 Dodge Caliber. I have actually created a link for you that shows all the chains that fit your tire size. I have included a link to a video review of these chains and a link to 2 FAQ articles on tire chains for you. You will also want to consult your vehicle owners manual to determine if there are any specific recommendations or restrictions for chain use.
view full answer...

Can the CE Smith U Bolt # CE15253A Be Used to Mount the CE Smith Offset Spool Roller # CE32150G
The CE Smith U-bolt # CE15253A could be used to mount the CE Smith Offset Spool # CE32150G. The diameter of the u-bolt and the mounting bracket of the offset spool are both 7/16 inch, and are compatible. I have included a video demonstration of the CE Smith Offset Spool for your reference.
view full answer...

Trailer Hitch and Bike Carrier for a 2010 Dodge Caliber Mainstreet
Starting with the trailer hitch, the Draw-Tite hitch # 24769 that you have selected is a correct fit for your 2010 Dodge Caliber Mainstreet. And the Swagman bike carrier # S64670, will fit the hitch and your Caliber as well. I have linked a video showing this bike rack on a 2011 Caliber. If all you want to do with the hitch is use it for a bike rack then you will not need a ball mount at all. If you do plan on towing a trailer then you would need ball mount # 3591, a 1-7/8 inch ball #...
view full answer...

Will Covercraft SeatSavers # SS2376PCSA Fit 2009 Dodge Caliber With Front Seat Side Air Bags
I spoke with my contact at Covercraft and the Covercraft SeatSavers, part # SS2376PCSA, you have referenced is not designed to fit on a 2009 Dodge Caliber that has side air bags in the front seat. They said the part # SS2376PCSA will fit the 2007 to 2009 Dodge Caliber front bucket seats with adjustable headrests, without the flat folding passenger seat. The other part # SS2375PCSA that is for the 2007 to 2009 Dodge Caliber is designed to fit the front bucket seats with adjustable headrests,...
view full answer...

Will the Draw-Tite # 24769 Work with Curt Cargo Carrier # 18145 on a 2011 Dodge Caliber
I went out to the ware house and pulled the Draw-Tite Class I Trailer Hitch, # 24769, and the CURT Cargo Carrier, # C18145, and did some measuring. The dimensions I got are 10-1/2 inches from the closest part of the carrier to the center of the most rearward attachment hole on the hitch. I produced a short video showing how I took the measurements and explaining how I would go about determining if the 6 inch measurement for the cargo carrier would be sufficient for your 2011 Dodge Caliber....
view full answer...

Fit & Compatibility of Brophy Hitch Adapter 1-1/4 to 2 Inch on a Draw-Tite Trailer Hitch
The Draw-Tite # 24769 hitch is confirmed to fit your 2007 Dodge Caiber as long as it isn't an SRT-4 model. The Brophy hitch adapter # HT5R will fit into the Draw-Tite hitch but it will reduce the tongue capacity of your hitch by 50 percent. Which will then limit you to only 100lbs of tongue weight. Depending on the weight capacity of your Caliber it could be less. You will want to check the placard on the inside of your drivers door or your owner's manual (page 257) to see what your...
view full answer...

Trunk and Hitch Mounted Bike Rack Options for a 2011 Dodge Caliber
The Thule OutWay 3 Bike Rack, # TH56BV, will fit on your 2011 Dodge Caliber as long as it is not the SRT4 model with the rear spoiler. The clips will attach to the top and bottom of the rear hatch and a spoiler cannot support the weight of a trunk mounted bike carrier. If you have a rear spoiler, then I would recommend a hitch like our Draw-TiteTrailer Hitch, # 24769, and one of our most popular hitch mounted bike racks the Thule Camber 2 Bike Rack, # TH9058. You may also want to get...
view full answer...

Best Lock When Carrying Schwinn Clear Creek on Swagman XTC2 Bike Rack Is Frame Adapter Needed
I took a look at the Schwinn Clear Creek online, and am convinced that the upper frame bar doesn't plunge down so far that the frame hook of the bike rack wouldn't be able to hold it. You should be okay without using a frame adapter. As far as a lock goes, Swagman offers a combo hitch/cable lock part # S64031 that will secure the rack to the hitch and the bikes to the rack. No lock is completely foolproof, but this item will certainly deter theft and encourage would-be thieves to find...
view full answer...

How to Tow a Motorcycle with a 2008 Dodge Caliber
According to owner's manual for your 2008 Dodge Caliber the gross trailer (GTW) and tongue weight (TW) rating of your vehicle with the 2.0L I4 engine is 1,000 lbs and 150 lbs respectively. Therefore, I cannot recommend you use this vehicle to haul your motorcycle (206 lbs) and carrier (36 lbs) as this would exceed the tongue weight capacity of the vehicle. The only way I can offer you to haul your motorcycle is on the back of a trailer. In order to use this trailer you would need a trailer...
view full answer...

Will Hitch from 2010 Model Fit a 2007 Dodge Caliber
The Dodge Caliber was only produced for one generation, from 2007-2012. The 2007 and 2010 Dodge Caliber would indeed use the same hitch, such as the Draw-Tite Class I # 24769 you'd looked at. If the hitch has previously been installed, I'd recommend replacing the hardware, as it isn't meant to be repeatedly torqued. You can obtain replacement hardware by using our # RHK replacement hardware kit. On the linked # RHK product page, simply input the hitch part number into the provided field...
view full answer...

Correct Installation Kit for a Westin Safari Light Mounting Bar
The brackets we have for a Westin Safari Light Mounting Bar item # 30-0025 is the Custom Installation Kit for Westin Safari Light Bars item # 30-1345. This bar will only fit the following vehicles: 2002-07 CHEVROLET TRAILBLAZER 2002-04 GMC ENVOY 2003-07 ISUZU ASCENDER 2004-07 BUICK RAINIER and OLDSMOBILE BRAVADA It does not fit a 2008 Dodge Caliber nor is there a light bar or bull bar that is custom made for this type of vehicle.
view full answer...

Second Vehicle Kit For Roadmaster Even Brake with Serial Number 005227
It sounds like you need the Roadmaster Even Brake 2nd Vehicle Kit part # RM-98400 since the serial number is lower then 27,496 you can use this kit as confirmed by Roadmaster.
view full answer...

Will the Thule Passage 2 Bike Carrier # TH910XT Fit on a 2008 Dodge Caliber
The Thule Passage 2 Bike Carrier, # TH910XT, will fit your 2008 Dodge Caliber as long as your Caliber does not have a plastic rear spoiler. If your Caliber has no spoiler or a metal spoiler that is part of the body of the car, then the Passage bike carrier is an excellent choice. If your vehicle has a plastic spoiler at the top of the hatch, I would not recommend using a trunk mount bike carrier. Trunk mount bike carriers place additional weight on spoilers and plastic spoilers were not...
view full answer...

Will Tow Ready T-One Vehicle Wiring 118552 Fit a 2008 Dodge Caliber R/T
Yes, the Tow Ready # 118552 T-Connector is a fit for all models of the 2008 Dodge Caliber (except SRT4), and will work on your R/T model. The installation is fairly simple, as the wiring just plugs into the back side of the vehicle tail lights, between the light and factory wiring. You will also need to run the red power wire along the bottom of the vehicle and connect it to the positive terminal on the vehicle battery, with the included fuse and fuse holder in line. I would recommend...
view full answer...

Is Adapter Needed To Install TriLift Scooter Lift on 2007 Dodge Caliber With a Class I Hitch
I looked up the TriLift scooter lift and they list the lift as working on a Class I 1-1/4 inch hitch, but they limit the weight of your scooter to be less than 115 lbs. The Hitch Adapter, part # 80303, that you have referenced, can only be used with a Class II receiver. The only hitches available for your 2007 Dodge Caliber are a Class I hitch. The #80303 hitch adapter will not work. The problem when using a hitch adapter is that you will reduce the tongue weight capacity of your hitch...
view full answer...