Yes, the Curt Trailer Hitch # 13465 would work well with a Swagman bike rack to carry your mountain bikes and is a fit for your 2010 Dodge Challenger.
I am not sure which Swagman bike rack you are considering so I attached a link that has all of the Swagman bike racks we offer.
You should note that all non-trailer loads - bike racks, cargo carriers and so forth - should be supported with stabilizing straps. Failure to properly support these loads will void your hitch warranty from CURT.
For... view full answer...
I spoke with my Curt representative about the fit of their # C12064 Class II hitch on a 2015 Dodge Challenger. Although they don't have any photos available (we don't either), I was told that although there were cosmetic changes made to the rear of the 2015 Challenger, the fit itself hasn't changed. The hitch will fit without needing to alter the rear bumper fascia. view full answer...
The only Pullrite Super Glide 5th wheel hitch that would work with the Curt Custom Fifth Wheel Installation Kit # C16444-204 is the Pullrite ISR series which is the 2700 or 2900 models.
For your Pullrite, you will need to get the rails from Pullrite if you do not have a 2700 or 2900 series hitch. If you do have this hitch, then the Curt Custom Fifth Wheel Installation Kit # C16444-204 will work fine. view full answer...
We haven't had the chance to install the Curt Trailer Hitch Receiver # C13236 on the SXT Plus model of the 2017 Dodge Challenger as of yet but it does not require any trimming of the fascia on other models.
I've attached a picture of how the hitch looks when installed on a Challenger for you to see. view full answer...
Yes, the Vehicle to Vehicle Tail Light Converter # C56196 will allow you to separate your stop and turn signals on your 2012 Dodge Challenger.
Please keep in mind it is recommended you use Diodes # 48955 to prevent power feedback.
I have added a link to a video review of the converter for you to check out as well. view full answer...
The Curt Trailer Hitch Receiver part # C13236 weighs around 32 lbs and the Curt Trailer Hitch Receiver part # C12064 weighs about 26 lbs. The Curt C12064 is a 1-1/4" hitch receiver and the Curt C13236 is a 2" receiver. I normally recommend a 2" hitch because you will have more options for bike racks and other accessories. They also normally offer more weight capacity.
In this case I do recommend the 1-1/4" hitch part # C12064 because it is a concealed cross tube hitch so the only portion... view full answer...
Thanks so much for that info, and to replace your current leaf springs that are 24 inches apart from center eye to center eye, you want springs that are slightly shorter because over time they flatten out. So for replacements I recommend 23-1/8" long springs:
- 3-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 23-1/8" Long # e59SR
Then to replace your equalizer with a MORryde equalizer, you'll want to measure your axle from center to center, which will be your wheelbase, and the correct... view full answer...
The Draw-Tite Class II Trailer Hitch Receiver, # 36548, will fit a 2016 Dodge Challenger if your vehicle does not have the quad-tip exhaust. Since your model is the Hellcat, I am assuming that your vehicle will have the quad-tip exhaust.
I recommend the Curt Trailer Hitch Receiver, # C12064. This hitch is designed to fit either exhaust model of the 2016 Dodge Challenger. The Curt hitch uses the 1-1/4 receiver opening and has a max tongue weight rating of 350 lbs.
The Curt hitch is required... view full answer...
In order to install a trailer hitch on a 2019 Dodge Challenger with aftermarket exhaust, the best option we have for you is the Curt Trailer Hitch Receiver part # C13236 not the Draw-Tite Max-Frame Trailer Hitch Receiver part # 76145. The Curt hitch as you can see has a smaller bracket profile than the Draw-Tite hitch so there will be a better chance of compatibility.
That said, there would not be a way to confirm fit as none of the trailer hitch manufactures do any test fitting with... view full answer...
If your turn signals work at first and then stop, even though your turn signal is still on in your 2009 Dodge Challenger, it sounds like you have a problem with your ground wiring.
You will want to make sure your grounds are securely attached to bare metal surfaces free of any paint, dirt or corrosion of any kind. It is also a good idea to ensure that each of your trailer lights has its own ground, which will help eliminate one light causing an issue with other lights on your trailer.
I... view full answer...
The Curt Adjustable Width Trailer Hitch Receiver for RVs # 13703 is a great option. It's extremely versatile since it can be bolted or welded on and fits C-channel, I-beam, and box frames. It's designed to fit frames from 22 to 72 inches wide.
You may want an adjustable ball mount on the RV like the B&W Tow & Stow # BWTS10037B. This comes with two different sized hitch balls and has a 5 inch drop and 5-1/2 inch rise.
You'll will want to check with the DOT in your area and the areas... view full answer...
I have a solution for you but the Curt Trailer Hitch item # 13465 will not give you enough clearance to mount the Kuat Sherpa 2.0 Bike Rack for 2 Bikes item # SH22B. The hitch pin hole sits too far underneath your car when installed.
Instead you will want the Draw-Tite Trailer Hitch item # 76145. This hitch is custom fit and bolts to your Challenger with included hardware. The hitch pin hole sits 6" from the edge of your bumper and the closest part of the Sherpa 2.0 when folded up is... view full answer...
Both RockyMounts TomaHawk Roof Bike Rack for Fat Bikes - Wheel Mount # RKY1222 and the SeaSucker Komodo Trunk Bike Rack - Fork Mount - Vacuum Cup Mounted # 298-BK1910-AB come with all the hardware you need attach your bikes.
As far as transporting kayaks, you will attach the kayaks to the SeaSucker Monkey Bars Roof Rack - Vacuum Cup Mount # 298-SX6000B. For a compatible kayak carrier, I recommend the Yakima SweetRoll Kayak Carrier w/ Tie-Downs # Y04074. The SweetRoll will allow you to... view full answer...
For the Draw-Tite Max-Frame Trailer Hitch item # 76145 you are going to want the Curt Towing Starter Kit for 2" Hitches item # C45534. This towing kit will provide you with a 2" ball and a fixed ball mount with a 3/4" rise and 2" drop. It also includes a hitch pin and clip, hitch receiver lock with keys, hitch cover, and a storage case.
This hitch is confirmed to fit your 2010 Dodge Challenger unless you have the quad tip exhaust. If you have the quad tip exhaust you will want the Curt... view full answer...
Thanks for the photo, and the rear diffusers on your 2020 Dodge Challenger would have to be removed in order to install a hitch like the Curt Trailer Hitch Receiver # C13236 which fits your car.
Based on the photo, the diffusers go under the bumper a bit, so they would likely interfere with the hitch. It would be close, but from looking at the photo I think they would have to come off.
I have added a link below to a video install for you to check out as well of the Curt Trailer Hitch... view full answer...
Yes, you can absolutely put a trailer hitch receiver on a 2015 Dodge Challenger, and what you will need is a hitch from Curt:
- Curt Trailer Hitch Receiver # C13236
This is a Class III hitch with a 2" receiver so it will be able to accept whatever accessory you are looking to use with it. If you want the hitch to do some light towing you will also need the T-One Vehicle Wiring Harness # 118656.
I have added a link below to a video review on a similar model year Challenger for you to... view full answer...
The Curt Trailer Hitch Receiver # C12064 is currently the only receiver we have confirmed to fit the SRT Demon for your 2018 Dodge Challenger. This is a class II receiver as the larger class III receivers will not fit the SRT Demon trim. The receiver is rated for up to 3,500lbs trailer weight with up to 350lbs of tongue weight. Be sure to contact your Dodge dealer for your exact towing specifications.
You will need the T-One Vehicle Wiring Harness # 118656 to connect to most small trailers... view full answer...
I apologize for the confusion, but basically the Curt hitch part # C12064 fits both the the quad tip and non-quad tip versions of the 2019 Dodge Challenger so it will fit and work well for you.
I attached an install video link to this page plus a picture of what it looks like installed for you to check out too. view full answer...
Yes, the Curt hitch part # C13093 that you referenced has been confirmed as a fit for your 2016 Dodge Challenger SRT so it would work well for you.
It does fit a few Chrysler vehicles though so I can understand the confusion.
I attached an install video that shows it getting installed on a similar 2013 Challenger.
For trailer wiring you would want the part # 118656.
If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts;... view full answer...
Go To Results