Yes! The Adco Windshield Cover # 290-2402 is confirmed to fit your 1989 Dodge B250 Van. The cover actually fits 1973 - 1997 Dodge Vans like what you have. The review video, which I have linked, is just for demonstration purposes only. view full answer...
According to my contact at Draw-Tite, as long as the bumper you describe is an OEM bumper that is not a step bumper, the # 75140 hitch would be a fit.
As we have not had the opportunity to install this hitch on a 1987 Dodge Van, I cannot say with certainty how much clearance you will have behind the bumper. The instruction sheet for the # 41910 (see link) shows a cross-section view in the upper left corner of the page. As you can see, the hitch pin hole is pretty close to the rear edge... view full answer...
While we don't currently have a custom-fit front mounted hitch available for a 1994 Dodge Van B250 we do have universal fit options like Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-07 with a 7" drop bracket or 16" drop # 41990-16. These would both need to be welded to the frame and would require a bit of fabrication/alteration to the front bumper/fascia in order to fit. view full answer...
While we do have suspension enhancement that will fit your 1994 Dodge Van with a B350 chassis, the part you mentioned will not fit your van.
Instead, for a similar jounce-style spring what you will need is the Timbren Rear Suspension Enhancement System # TDVR350R.
These will do a great job of giving your van the support it needs to improve it's handling and stability, reducing body roll and absorbing shock. I have added a link to a video review for you to check out as well of the Timbren... view full answer...
The Roadmaster Rear Anti-Sway Bar # RM-1129-111 that you referenced sits in front of the rear axle with just a little of it sitting behind, but it shouldn't be enough to interfere with the large fuel tank that you have on your 1991 Dodge B250. My contact at Roadmaster confirmed this.
I have attached a link to the installation instructions for you to reference. view full answer...
We currently do not carry any bike racks that are specifically for the front bumper of an RV. There are a couple reasons for this; bikes mounted on the front of the vehicle can block your line of site, headlights and turn signals and the airflow to your engine. If your RV has a continuously welded steel bumper that is between 4"-4-1/2" wide you could make the Swagman Around the Spare 2 Bike Rack # S80501 work, but again, I'm not sure it would be the safest option for you unless you mounted... view full answer...
I spoke with my contact at Tekonsha who said that from the back of the 7-Way connector to the tip of the plug is about 8" on the T-One # 20135. view full answer...
I contacted our representative at Classic Accessories and he recommend a Model C Cover, which fits boats 16 feet to 18-1/2 feet long. view full answer...
The Draw-Tite Class III Max-Frame Trailer Hitch Receiver part # 75140 will only fit a Dodge Van from 1978-2003. This is a custom fit trailer hitch so it is designed specifically for the Dodge Van which is why it will not fit any other models. This is the same for the majority of custom fit trailer hitches save for models that share the same chassis like the GMC Terrain and Chevy Equinox. view full answer...
We do have a leaf spring suspension helper kit for your 1990 Dodge B250 2WD van, SuperSprings Suspension Stabilizer and Sway Control Kit # SSA7MTKT and others types that are shown on the linked page, but the RoadActive RAS # RAS4611-DV is not a fit for your B250.
The SuperSprings # SSA7MTKT bolt on above your OEM leaf springs and reinforce them to reduce sway from passing trucks, wind and when cornering. They adjust themselves automatically based on the load on your OEM springs and they... view full answer...
The Roadmaster Rear Anti-Sway Bar part # RM-1129-111 is a fit for a 1996 Dodge Roadtrek with or without water tanks to the best of my knowledge. That said, these water tanks may have to be removed for installation but only temporarily to get the anti-sway bar in place so this is still an option for you.
If you want to go with the RoadActive Suspension Custom Leaf Spring Enhancement Kit part # RAS4612-DV this would work as well but it will also stiffen the rear suspension as would any... view full answer...
The Curt # 13590 is confirmed to fit on the 1997 Dodge B3500 that has the factory step bumper. If your van doesn't have the step bumper, an option is the Curt # C13041.
Both are designed for the Dodge Vans and are built to accomodate the different styles. view full answer...
The multi-plug connector # 20135 does have the mating rectangular connector that will plug into the one on your 2003 Dodge Van. This connector is meant as a replacement. If your van did not come with a factory installed 7-Way, then it is possible that only the light functions will be active.
If the van did not come with a factory trailer connector and the pins on that rectangular connector are not active (which you can test with a circuit tester such as # PTW2993) then to add a 4- and... view full answer...
The mounting bracket measures 4-1/4 inches from the back of the plate to the back of the upright on the rack. Make sure this is enough distance to clear the spare tire. You would measure from the flat sheet metal where the spare tire studs are attached and measure out through the center hole of the wheel until you clear the tire.
If you should find that the SportRack model will not work for you, The Yakima SpareRide 2, # Y02599 comes with two different extensions to fit oversized spare... view full answer...
The RAS Kit # RAS4611-DV can work in conjunction with the Roadmaster Anti-Sway Bar # RM-1129-107.
They have similar purposes but I think you'll gain a little bit from the RAS kit over the anti-sway bar. The RAS will strengthen the leaf springs and help with overall suspension. This will in turn help with sway like the anti-sway bar will. In addition, the RAS will reduce body roll while cornering which is often a major concern with a heavily loaded van.
Keep in mind neither will increase... view full answer...
Curt trailer hitch # 13590 is designed to fit 1997 to 2003 full size Dodge vans with the factory step bumper. Your 1-ton van is a full size model so as long as it has the factory step bumper the hitch will fit.
If it has the standard bumper and not a step bumper then the Curt hitch you would need is # C13041.
For either hitch I recommend etrailer ball mount kit # EBMK2216. It comes with a ball mount with a 1 inch rise or 2 inch drop, 2 balls, and hitch pin with clip, and a storage bag.... view full answer...
It's very possible that the Saris SuperClamp EX 2 Bike Platform Rack # SA4025F will fit with the spare tire on your 1989 Dodge ram Van. From the center of the hitch pin hole to the closest tray on the SuperClamp EX measures 12". If you have no less than 12" from the center of the hitch pin hole on your Van to the outermost part of your spare then you should be good to go as you can adjust the bike rack so that the handlebars of your bike can face in either direction.
If you have a greater... view full answer...
The B&W Heavy-Duty Trailer Hitch Receiver # BWHDRH25198 fits a variety of pickups but you'll need a different hitch for your 2000 Dodge Van 3500.
From the linked selection I recommend going with the Curt # 13590 if you have the factory step bumper or the Curt # 13015 if you have the standard bumper.
If you plan on using this for towing then I recommend using the Tekonsha Wiring # 118368 and checking out Ball Mount Kit # 989900 because it includes two ball mounts, one with a 3/4” rise/2”... view full answer...
I recommend checking out the Curt Trailer Hitch Receiver # C13041 for your 1997 Dodge Van with the regular bumper.
This is a Class III hitch with a 2" receiver rated for 600 lbs tongue and 6,000 lbs towing so it will be prefect for basically any application for you - just be sure you check these weight ratings with what your van itself is rated for and that you don't exceed the lower of the two.
If you plan on using this for towing then you also need the Curt Wiring Kit # C59236 and a... view full answer...
Thank you for all the helpful information you have provided with your question. First you want to make sure the Thule EasyFold XT 2 E-Bike Platform Rack part # TH903202 doesn't clear your spare tire. It is 9" from the center of the hitch pin hole to the closest part of the carrier. If you measure from the center of your hitch pin hole on the hitch past the spare tire and your measurement is less than 9 inches then the EasyFold will clear the tire.
You can use an extender but it will cut... view full answer...
Go To Results