Expert Answers about Ford Expedition

• Parts Needed to Add 7-Way to 2009 Ford Expedition and Install Brake Controller
• For your setup what you would need to install a brake controller and have a fully functional 7-way is the brake controller install harness part # ETBC7. This comes with a 4-way to 7-way adapter and all of the wiring needed to install the controller. To complete the 12 volt power circuit you will need 10 gauge wire like part # 10-1-1 with a circuit breaker part # 9510 to run the wire to the positive terminal of the battery. The reverse light circuit would get completed by tapping into...
  view full answer...


• Solera RV Slide Topper Awnings For 61 And 151 Inch Flange Measurements
• We have what you are looking for. You will need the Solera RV Slide-Out Awning - 5'7" Wide - 48" Projection - White # LCV000163274 and the Solera RV Slide-Out Awning - 13'1" Wide - 48" Projection - White # LCV000163300. You need to have 2.5 inches of overhang on each side of the topper for the unit to work proper. These two units will give you the overhang you need.
  view full answer...


• Recommended Towing Mirrors For A 2021 Ford Expedition Max Limited
• The CIPA Custom Towing Mirror # CM11402 and # CM11401 are for a Dodge Ram truck. For A 2021 Ford Expedition there isn't a confirmed fitting slip on tow mirror so you'll need a universal tow mirror instead. I recommend the CIPA Universal Towing Mirrors # 7070-2. These universal towing mirrors clip over your existing side-view mirrors to give you extended lines of sight. Dual strap system creates a snug fit and the textured straps prevent loosening over time.
  view full answer...


• How to Monitor the Battery with Go Power Solar Extreme Charging System # 34282185
• The Go Power Solar Extreme Charging System # 34282185 includes a fixed-mount remote which lets you control and monitor the inverter charger. You do not need an external battery monitor. Check out the video linked below for more details.
  view full answer...


• Recommended Towing Mirrors for 2014 Ford Expedition with Power Folding Mirrors
• For your 2014 Ford Expedition with the power folding mirrors I recommend the K-Source Universal Dual Lens Towing Mirrors # KS3990. I like these mirrors a lot because of the ratcheting strap system they use to create a really secure and snug fit to the factory mirror housing. This works to eliminate a lot of the vibration and movement during travel that is present on most alternative options. Because these simply attach to the factory mirror housing they won't interfere with the power folding...
  view full answer...


• Which Locks Can I Use with a Yakima Sweetroll Kayak Carrier
• The Yakima Sweetroll Kayak Carrier # Y04074 does not come with lock cores but you can add them with the Yakima Same Key System (SKS) Lock Cores # Y07204 (pack of 4). If you just need a single lock core replaced and it has A137 stamped on the body of the core, you can use the # Y8771-A137 as a replacement that will work with your current keys. If you've got a different number stamped on the lock cores or your existing key, let me know what number you've got and I can help you locate the...
  view full answer...


• Parts Needed to Flat Tow 2017 Ford Expedition With MCI Bus
• You are correct, as long as your frame does not exceed 44" you will be able to weld on the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld On - Class V - 2" # 41990-07. Weight distribution isn't an issue and is not something you would use for flat towing your 2017 Ford Expedition. In addition to the hitch you will need the following to flat tow your vehicle: - Demco Classic Base Plate Kit # DM9518296 - Demco Dominator Non-Binding Tow Bar # DM9511008 - Roadmaster Diode...
  view full answer...


• 7-Way and 4-Way Recommendation for a 2007 Ford Expedition
• The only 7-way/4-way we offer that would do what you are looking to do would be the # HM40975-11998 that has a connector that plugs into the back of the 7-way. The benefit to this style of connector is that it if you ever need to replace the 7-way you wouldn't have to rewire the whole thing and you could just replace the connector. If you have the round plug already all you would really need is the part # HM40975 though.
  view full answer...


• When to Replace Hitch Pin
• Minor corrosion can be addressed with cleaning and coating the pin to prevent further issue but if your pin is bent I suggest you replace it. As for the useable life of a hitch pin, that cannot be established due to too many variable such as environmental conditions, and use during time frame. To put a definitive length of time toward usability is difficult however, if you have damage in any way, including bending, I would immediately replace before it possibly fails. We have a wide...
  view full answer...


• Reusable Air Filter for 2019 Ford Expedition
• Part # AR851-385 works for your 2019 Ford Expedition. This is a dry style filter so you won't have to worry about oiling it after cleaning the filter. This is also a reusable filter which means you just wash it out, let it dry, and reinstall the filter into your vehicles air box.
  view full answer...


• What is Required to Install the Curt Front Hitch C31083 on a 2018 Ford Expedition
• The Curt Front Mount Trailer Hitch Receiver part # C31083 will require a slight trimming of the lower plastic bumper fascia but there will be no drilling or alterations that will be needed on the vehicle's frame. The trimming of the lower plastic bumper fascia is needed to allow for the receiver tube opening to poke through which you can see in the attached photo on a similar truck. The brackets install using pre-drilled holes in the frame rail. This means that no warranties will be voided.
  view full answer...


• Height Added to 2019 Ford Expedition Max With Rhino Rack Vortex Stealthbar Installed
• When the Rhino-Rack Vortex StealthBar Roof Rack # RRSX100 is installed on the roof rails of your 2019 Ford Expedition it would add roughly 1-1/2 inches to them. The bottom of the bar that runs across the roof will be right at the same height as the top of the raised rails so if you were looking for clearance under the bar you could lie a straight edge from one rail to the other and see. The dimension would get smaller as you get closer to the center of the roof since the roof is curved.
  view full answer...


• WeatherTech Cargo Mat Recommendation for Covering Folded Third Row of 2015 Ford Expedition
• The part # WT40222 will fit your 2015 Ford Expedition and will go all the way up to the back of the second row of seats when the third row is folded down. If you had the third row up though you'd have to go with the part # WT40223 instead as there's no way to do what you mentioned with a mat designed for covering the third row.
  view full answer...


• Replacement Taillights for Coleman Lantern 244BH
• I checked out several pictures of the rear of a Coleman Lantern 244bh and the taillights they all use are the part # AST60B and part # AST61B so these would be what you would need.
  view full answer...


• Universal Towing Mirrors for 2017 Ford Expedition
• We have universal-fit towing mirrors for your 2017 Ford Expedition but they will not be the same as the custom-fit ones that are made specifically to fit an F-150 pickup. Popular choices are the K-Source 2-mirror sets # KS3990 and # KS3891-2. Both offer tool-free clip-on installation. Mirrors # KS3990 are a dual lens design while # KS3891-2 have a single large mirror glass. Both offer manual adjustment.
  view full answer...


• Installing Brake Controller Wiring Adapter Part # 3035P on 2004 Ford Expedition
• The connection point for the brake controller should be located under the dash just above where where your right leg would be if you were behind the wheel. I have an installation video that shows the location of the connector. The video shows an install on a 2007 Expedition, but the procedure would be similar on your 2004 model. The connector you are looking for is gray in color.
  view full answer...


• Recommended Trailer Hitch for 2019 Coachman Freedom Express Ultra Lite 248RBS
• On the Ultra Lite trailers like your 2019 Coachman Freedom Express Ultra Lite 248RBS, the manufacturers don't reinforce the bumpers to be able to handle that weight so the torque on the bumper is too great. The best solution is to use the Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" to 68-1/2" Wide # C13704 or up to 72 inch wide # 13703. This trailer hitch will mount to the frame of your trailer and will allow you to use a bike rack or cargo carrier on your trailer. If...
  view full answer...


• Will Westin Sure-Grip Running Boards Fit 2013 Ford Expedition With Factory Boards Removed
• Yes, you can use the Westin Sure-Grip Running Boards w/ Custom Installation Kit # 27-6630-1815 on the 2013 Ford Expedition that has the factory electric running boards completely removed. The only thing that may be different is the holes that the brackets install into. I do not know how many brackets the factory boards used but the Westin Boards use 3 brackets. I have attached a diagram that shows where they install. You may need to drill if the older system didn't require the same amount...
  view full answer...


• Will the Coil SumoSprings Custom Helper Springs CSS-1145R Fit a 2016 Ford Expedition 2WD
• I spoke with Super Springs about the Coil SumoSprings Custom Helper Springs part # CSS-1168R for your 2016 Ford Expedition. The issue is not that it is not a fit but rather they have not yet had a 2WD model in to test them on. Therefore, in order to confirm compatibility I would need you to take the measurements I have attached for you. In regards to using the Coil SumoSprings with your E-Z Lift Max Weight Distribution System, this will not be an issue at all but as you mentioned you...
  view full answer...


• Will the Lockrack Watersport Carrier Fit a 2016 Ford Expedition with Factory Crossbars
• The Lockrack Watersport Carrier part # 339LRUNISETA will work just fine with the factory roof rack on your 2016 Ford Expedition so you don't need to replace this. That said, you will need to be mindful of your usable crossbar space in relation to the width of your kayak/boards but this should not be too much of an issue for most kayaks/boards.
  view full answer...