For the Coglan's Hammock Carabiner # CG86UV The inner width at the top is 1-1/16" the inner width at the bottom is 5/8" and the latch open is 1/2". view full answer...
I attached an FAQ that details how to pick out the correct ball mount. Picking out the correct ball mount will allow your trailer to sit as level as possible. Basically you will first measure the height from the ground to the top of the receiver opening on the hitch while on level ground. Next, you will measure the coupler height from the ground to the bottom of the trailer coupler when the trailer is on level ground.
Next, you will need to compute the difference. If the hitch height is... view full answer...
The valve stem of this Americana Metal, Bolt-In Valve Stem # AM20906 that you referenced is 1-1/4 inches long in overall length.
I attached an FAQ on trailer tires for you to check out also. view full answer...
I went out to our warehouse to take a look at the Malone 2" Dual Purpose Hitch Receiver # MPG544 referenced in your question. I measured a distance of right at 9 inches from the center of the main hitch pin hole to the back edge of the top receiver.
I have attached an image with these dimensions labeled that you can also check out. view full answer...
I pulled a Camco Propane Cylinder Gas Gauge and Leak Detector # CAM59023 from our warehouse to measure its length and determined that it is 3-3/4 inches in length. view full answer...
I did a little research and it looks like the towing capacity of your 1999 Ford Expedition Eddie Bauer 4x4 is 7,900 pounds maximum. I looked up the 2010 Jayco M-32BHDS trailer and it has a dry weight of 7,765 pounds and a gross weight of 9,750 pounds. Once you have the trailer loaded with water, gas, and cargo it will likely exceed the 7,900 pound capacity of the vehicle. I advise looking at a lighter weight trailer, something with a gross weight under 7,900 pounds such as the M-29BHS. view full answer...
When fully compressed each of the hoses that come with the RhinoEXTREME # CAM39867 will measure 54 inches minus the elbow as that wouldn't fit in a RV bumper. view full answer...
A 4 on 4 inch bolt pattern is measured diagonally on center. The first number indicates the number of lug holes and the second number indicates the diameter of the circle that those holes sit on. Check out the wheel bolt pattern help article that I attached. I have also attached a link to all of our 12 inch trailer wheels and tire/wheel combos that have a 4 on 4 inch bolt pattern for you to check out. view full answer...
The weight of the Flow Through Tire Sensors for TireMinder TPMS # TM66FR is 0.7oz each including the CR1632 battery. According to TireMinder, these should not throw off the balance of your tire. That being said, you could always have them checked at a local tire shop for peace of mind once the sensors are installed. view full answer...
Dexstar Steel Mini Mod Trailer Wheel # AM20545 does not have any offset. I confirmed this with Dextsar. It sounds like you are asking about the backspacing which is the distance from the mounting flange to the outside of the rim.
Since this is a 6 inch wide rim the back spacing is 3-1/2 inches. To determine this you take the overall width of the rim and add an additional inch for the lip on the wheel and then divide by 2. view full answer...
I have a solution but hitch extensions really shouldn't be used with weight distribution setups. Your best solution would be a new weight distribution shank that is longer which would give you the extension you are needing to clear you jack.
For that we have the part # C17122 which is 18 inches overall and is our longest option. It's also compatible with all of the standard weight distribution heads too which means it'll fit the system you have now. view full answer...
The etrailer Tongue Weight Scale # e99044 will give you a good idea on tongue weight, but if you're looking for high accuracy I would find an alternative. There is no accuracy rating available for this scale. It will give you a ballpark idea but in your case where a slight difference matters it is not the best choice. You should find a scale with more tick marks or digital readout so you know exactly where you're at. view full answer...
To flat tow a 2019 Ford Expedition Max 2WD you will need the following parts:
Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect item # e84ZR
Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit - Removable Arms item # RM-524457-5
Wiring Harness - Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit item # RM-15267
Charge Line Kit - Roadmaster Battery Charge Line Kit for Towed Vehicles item # RM-156-25
Supplemental Braking System - Blue... view full answer...
I went out to the warehouse and pulled one of the Pro Series Snap-Ring Swivel Jacks, # PSEJ10000101, to measure for you. I added dimensions to a photo I took of the mounting plate for you to use to see if the mounting pattern will match up to your mounting plate on your LAK sailplane trailer model T-5.
The overall dimensions of the mounting plate are 6-3/8 inches by 5-1/2 inches, and the bolt hole pattern is 4-3/8 inches on center for the outer most holes, 3-3/8 inches on center for the... view full answer...
I went out to the warehouse and measured Curt trailer hitch # C13704 for you. The distance from the top of the mounting flanges to the top of the cross tube is 2 inches. I have included some pictures with additional measurements for you. view full answer...
I went to our warehouse to measure the included drain plug on the Derale Transmission pan cooler # D14208 and it is 1/2 inch 20 threads straight. The inner diameter of the drain hole is 0.44 inches using a digital caliper tool.
I made a couple diagrams for you to look at too. view full answer...
You are correct the Front Pair WeatherTech Mud Flaps item # WT110088 are confirmed to fit your 2022 Ford Expedition. As far as rear ones go, I reached out to WeatherTech and confirmed that the item # WT120088 do not fit the 2022 Expedition. view full answer...
I pulled the Curt Bumper Mount Hitch, # E-3S, from the warehouse and made a video showing you the measurements that you were asking for. The wider holes, closest to the receiver opening, are 1-1/4 inches wide and accept a 3/4 inch diameter bolt. The bolt holes measure 10-3/4 inches at their widest points and 7-1/4 inches at their closest point.
With the bolts set at the widest point, they measure 9 inches apart on center and 8 inches apart at the closest point. view full answer...
As you can see in the photo I've edited for you, the outside to outside dimension of the horizontal bend in the Curt # 13703 hitch mounting flange is 2-1/2 inches. view full answer...
The external dimensions of the battery box that comes with the TorkLift HiddenPower Under-Vehicle Battery Mount with Battery Box part # TLA7726 are 14" long x 10-11/16" tall x 10" wide. view full answer...