The panel under the driver dash of your 2018 Jeep Cherokee that will need to be removed in order to install a brake controller like the Tekonsha Primus IQ Trailer Brake Controller part # TK90160 is held in with a single screw. Once you remove this screw, the panel can then come off and expose the brake controller port that you will need for the Tekonsha Custom Wiring Adapter for Trailer Brake Controllers part # 3014-P. I have attached a photo of this for you that I took myself on a coworker's... view full answer...
I can help you with recommendations for the Roadmaster flat towing items you'll need to tow your 2019 Jeep Cherokee Limited behind your motorhome. You might care to check out the linked article that covers all the needed items. It will give you a nice overview.
Starting with base plates, I suggest the Roadmaster EZ4 base plate # RM-521452-4, so long as your Limited does not have the Active Aid Shutters. These feature twist-lock draw bars which means there are no pins to get lost.
With... view full answer...
We have exactly what you need! The Curt Trailer Hitch Receiver # C13395 is a Class III trailer hitch with a 2" receiver that is designed so that the receiver is the only portion that is visible (see attached picture).
Since you are planning on towing you will also need a wiring harness item # C56406 and a ball mount kit item # C45534. view full answer...
I have the perfect brake controller for your 2020 Jeep Cherokee Trailhawk. It is the Redarc Tow-Pro Liberty Brake Controller item # RED24FR. This is a proportional brake controller that will engage your trailer's brakes when your Jeep decelerates. It activates immediately and is not time delayed. The Tow-Pro Liberty has a unique installation method that allows you to mount the main control unit out of sight behind your dash. The only part visible is the control knob.
We have a couple... view full answer...
For your 2015 Jeep Cherokee and 6x10 trailer with 900 lb tongue weight, the way you determine fit is based on the total tongue weight which also adds any cargo behind your rear axle to your loaded trailer tongue weight. Then you want a system that has that total tongue weight in the middle of its range.
Based on your tongue weight of 900 lbs which I assume is the loaded weight, adding a little for any cargo behind the rear axle of your Cherokee, the most popular option is the Equal-i-zer... view full answer...
For your 2014 Jeep Cherokee Latitude with raised roof rails the Thule Aeroblade Edge roof rack part number # TH7501B-TH7502B is a confirmed fit and would be my recommendation. I like the aero shape of these and the fact that they do not extend past the feet of the rack. This allows the least amount of wind resistance and looks really nice as well.
The Thule Portage Canoe Carrier part # TH819 would then be a great carrier for the canoe. It comes with straps as well. view full answer...
We have what you are in need of.
Voyager PWM Filter for Voyager RV Camera Systems - Hardwire # VGR64VR.
Furrion Vision S Wireless RV Backup Camera System w/ Night Vision - Rear Mount - 5" Screen # FOS05TASF.
This will install in line with your wiring and will prevent the pulse with modulation issues. It will work with the Furrion Vision S Wireless camera. view full answer...
What you'll need to do is add a 7-way to your motorhome, and you'll just plug in your 4-way to a 7-way adapter and complete the wiring to your battery via a circuit breaker with the following:
- Adapter 4-Pole to 7-Pole and 4-Pole # 37185
- 40 Amp In-Line Circuit Breaker # 9510
- 10 Gauge Primary Wire # 10-1-1
The 10 gauge wire is sold by the foot so be sure to get the amount that you need. view full answer...
I do have an option for you but I am not aware of any way to flat-tow a vehicle using a front mount trailer hitch as there would be no way for the wheels to track properly. The most cost effective option we have for you to attach the Cherokee to your pickup is with the Curt Tow Bar with Adjustable-Width Arms part # C19745. If you don't have a steel bumper on your Jeep to attach this tow bar then you will need to remove the bumper and then attach this to the vehicle's core support.
In... view full answer...
Since your 2019 Jeep Cherokee Limited has combined wiring, if your Fleetwood Bounder does have separate wiring for its brakes and turn signals, you will need to use the Roadmaster Brite-Lite Wiring Converter # RM-732 when installing the Roadmaster Universal Hy-Power Diode Wiring Kit # RM-154 on your Cherokee. However, please keep in mind some motorhomes have combined signals that are separated at the tow vehicle wiring so you will want to verify this with your motorhome manufacturer.
Along... view full answer...
Yes, the WeatherTech Side Window Air Deflectors # WT82741 will fit your 2015 Jeep Cherokee Latitude . This dark-tinted 4-piece set will fit all versions of the 2014 and 2015 Jeep Cherokee. The easy installation instructions are linked for you. view full answer...
The Rhino Rack Euro Bars setup for the 2014 Jeep Cherokee naked roof is a square bar system that is now obsolete. Since square bars are not aerodynamic, they can create a lot of wind noise. To reduce the wind noise on this style of bars, a lot of our customers use a wind fairing to allow the wind to bounce off of the bar instead of whistling through it. For that I recommend Rhino-Rack Fairing for Roof Racks part # RRRF2 which will help the wind noise.
The best option is to switch out the... view full answer...
In order to install the Upgraded Circuit Protected Tail Light Converter Hardwire Kit part # 119178KIT on your 1995 Jeep Cherokee you will need to run each of the signal wires to the correct circuits which the best place to access these will be directly behind the taillights. If you need help with this you can use the video I have attached for you as a reference though it is not on a Jeep Cherokee. I am not sure what harness you are referring to but the above is the correct method to install... view full answer...
The Curt Trailer Hitch part # 13084 comes with 6 of grade 8, 1/2-13 x 1 3/4 carriage bolts. I recommend to clean the weld nuts with a brush like part # 814092 before trying to screw in the carriage bolts. It helps to use a brush and WD-40. I have attached a helpful article for your reference. view full answer...
The Thule K-Summit Chains part # TH02230K45 are the correct size for your 225/60-17 tires and come with the correct size lug adapter. I did some checking and it looks like your vehicle uses 19mm or 3/4 inch size lugs and these chains come with that size.
The height above the tire that chains will sit is 9.9mm. view full answer...
If you know you are going to be trading in your 2015 Jeep Cherokee at some point I would recommend the Blue Ox Patriot # BLU37TR instead. The Patriot installs very easily and works just as good as the DUO. If it were me that is the route I would go with.
I attached an install video for both kits for you to check out to see what the install would be like.
The downside to the Patiot would be that it removes from the vehicle everytime you get down flat towing it, but it's not difficult... view full answer...
If the signals are trying to draw more power when in function, but are only working intermittently, I would first check the ground contact point. This will be the white wire from the converter box. Make sure you have a clean, maybe even bare metal surface to give you a solid ground connection. You can use a little sand paper to remove any paint or coating to this surface that might hinder a quality connection when grounding.
Also look for any possible kinks or bends in the power from... view full answer...
If you have a new Brake Pro you would have the wireless transmitter and receiver in the package, but I have a solution that will work great for you.
I recommend the 12 Volt Outlet Kit, part # RM-9332. This is a kit that bypasses the cigarette lighter in the vehicle by attaching to the battery directly. It has a plug on the other end and you plug the Brake Pro into that. view full answer...
In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14".
To pick the correct cover, you will also need to know the type of hinge you need.
There is a 3 point hinge, such as the one on the Camco # CAM40153; a 4 point hinge as seen on the Camco # CAM40154; or a rolled metal continuous hinge like on the Ventline # BVD0449-A03; and universal hinge as shown on... view full answer...
Go To Results