The ground clearance of the etrailer Trailer Hitch Receiver part # e73ZR on a 2021 Jeep Cherokee is around 10" but this will vary from vehicle to vehicle. This is measured from the ground to the bottom of the receiver.
If you are planning on towing you will also need a wiring harness item # C56406 and a ball mount kit item # C45534. view full answer...
When you see "with trailer tow package" in the owner's manual for the 2015 Jeep Cherokee it is referring to the factory tow package for that vehicle. Factory tow packages vary from manufacturer to manufacturer but it does mean more than just have a hitch and wiring installed.
If your Cherokee did not come with the factory trailer tow package then it has a capacity of 2,000 pounds gross trailer weight. If it does have the factory tow package then it is rated for 4,500 pounds gross trailer... view full answer...
There are different carriers within the Thule Snowpack series (# TH732508, # TH7326, # TH7325, # TH7324 etc.) so I'll assume you mean the Thule SnowPack Ski and Snowboard Carrier # TH7326B. This is the carrier that can hold up to six pairs of skis or four snowboards.
When we measured it with snowboards mounted, we found it was 3-3/8" from the snowboard to the top of the crossbars. This measurement is with the clamp style. If you use the T-track mounting system, it comes with spacer that... view full answer...
For your Curt Trailer Hitch Receiver # C13172 on a 2014 Jeep Cherokee, you will have a height from the ground to the inside top of the receiver is 16 inches. I've attached a video that shows this. Then you will simply need to measure from the ground to the underside of your trailer coupler on level ground. Then you will do some simple math. If your hitch height is greater, use a ball mount with a drop--Hitch Height (A) - Coupler Height (B) = Drop (C). However, if your coupler height... view full answer...
The towing capacity of your 2017 Jeep Grand Cherokee Limited is 3,500 lbs when you have a trailer hitch like the Curt # C13172 installed.
For trailer wiring you'd then want the part # 118605 which installs without any splicing and has the most reliable converter box of all of the kits we offer.
If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise... view full answer...
If your travel trailer has a dry weight of about 4100-lbs, by the time you fill your water tanks and load all of your supplies and equipment you could easily reach or exceed the 4500-lb rated towing capacity for the 2016 Jeep Cherokee Latitude that has a 3.2L V6 and towing package. Ideally your choice of trailer would not be so close to the vehicle's maximum capacity.
Adding a weight distribution hitch like the Equal-i-zer # EQ37100ET does not increase the vehicle's towing capacity. This... view full answer...
The dimensions are listed in the installation instructions that I've linked for you. I've also copied the diagram for you.
The bolt plates aren't something you'll be able to find at your local hardware store, and the hitch manufactures don't sell them as an individual part. You'd need to use the entire hardware kit, which is actually a good thing, because you'll get all new hardware that's the correct size and grade (hitch installation bolts are only meant to be torqued one time.)
For... view full answer...
The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # 13160 has a 2 inch square receiver opening and the crossbar is 2-1/2 inch round tube steel. I went into our warehouse to measure it for you. It is a confirmed fit for 1984-2001 Jeep Cherokee models. view full answer...
The factory towing package is more than just a hitch receiver and wiring harness. Factory tow packages may include upgraded transmissions, suspension systems, brakes, engines, and cooling systems. The combination of that equipment is what determines your vehicles overall towing capacity. Your 2016 Jeep Cherokee Latitude is not capable of towing anything over 2000 lbs without the factory towing package and this isn't something that can be added afterwards.
The Curt Trailer Hitch Receiver... view full answer...
The distance between the mounting holes is indeed 36 inches for the Draw-Tite hitch that fits your 1999 Jeep Cherokee:
- Draw-Tite Max-Frame Trailer Hitch Receiver # 75054
I did verify for you with the manufacturer as well that the # 75054 will fit your '99 Cherokee. I also wanted to mention, if you are going to be using the hitch for towing and need a 4-way wiring harness for your Jeep, the correct part is the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118354. view full answer...
The gross vehicle weight rating (GVWR) of the 2018 Jayco Hummingbird 16FD travel trailer is 3500-lbs; this is the most it can weigh when fully loaded. Since properly loaded trailers have tongue weight (TW) in the range of 12- to 14-percent of the GVWR, your trailer will likely have TW of 425 to 500-lbs when loaded.
Actual measured TW is what you'll need to determine the correct weight distribution/sway control hitch to use. You can easily check your loaded trailer TW using the scale #... view full answer...
Yes, we do. It is the Lippert Replacement Hydac Cartridge Valve for RV Slide-Out Hydraulic Pump item # LC177094. I checked with Lippert and it is also designed to replace the part number WS08W-01T-C-N-0 valve for the leveling system.
I have linked a diagram of it below. view full answer...
Since the Removable Wheel with Pin # DL22539 has a 1,250 lb weight capacity it will be able to handle the 450 lbs of tongue weight you now have. Please note that this fits jacks that have a 2" inner tube.
A 3,500 lb trailer might be a bit difficult to move by hand though. If you find this to be the case you may be interested in the Trailer Valet 5X Swivel Jack and Trailer Mover # STC-V211. This installs by clamping around the frame of your trailer (up to 2-3/4" wide x 6" tall) and then... view full answer...
All the way to the left of the driver side floor board of your 2015 Jeep Cherokee there will be what is called a "dead pedal." This is basically just an area to rest your left foot while you are driving. If right in front of this area there is a raised section then you have a raised floor and the part # WT445661 that you referenced would fit.
If you do not have the raised floor you would need the # WT448331 instead. view full answer...
I checked with SumoSprings and for the # SSR-403-40 they list the dimensions as 10-3/4 inches tall, by 7-1/4 inches wide and a diameter of 4 inches. view full answer...
I measured the Tail Light Bars for Rock Tamers Mud Flaps - Qty 2 # ERT240, and the the most I felt comfortable stretching the longer wire was around 41 inches. Not stretched was around 14.5 inches. For the shorter wire, the most I felt comfortable stretching it was around 26 inches. Not stretched was around 11 inches. view full answer...
I went out to our warehouse to take a few measurements on the mounting bracket for the Brophy Camper Scissor Steps # AS24. The base bracket profile measures 24 inches long, 1 inch tall, and 1 inch deep. The shorter tabs that will be closer against the trailer/RV extend the bracket by just 3/8 of an inch, giving it an overall height of 1-3/8 inches. The slightly longer angled tabs that will actually attach to the step assembly extend the bracket by 5/8 of an inch, giving it an overall height... view full answer...
Congrats on the new vehicle! The best wiring kit for flat towing is going to be the Roadmaster Smart Diode 7-Wire to 6-Wire Wiring Kit for Variable Voltage LED Tail Lights item # RM63MR. The included diodes convert your 12V signal from your RV's wiring to a 9V signal so your tail lights work as intended. They also prevent electrical feedback that can damage your Jeep's electrical components.
I have listed the parts below that you will need to flat tow your 2022 Jeep Cherokee Trailhawk... view full answer...
Go To Results