In addition to the # RED44FR Redarc Tow Pro Elite, you'll also need the # RED49FR vehicle specific wiring adapter. The factory connector is located above and to the left of the emergency brake pedal as shown in the provided photo.
I've linked to a product installation video that you might find helpful. view full answer...
To be able to tow the Malone LowBed MicroSport Trailer # MPG464-LB with your 2018 Toyota 4Runner, you're just going to need a ball mount like the Curt Fusion Ball Mount for 2" Hitches # C45134 with a 2" hitch ball.
To choose a correct ball mount will dictate on the measurement from the ground to the top of the trailer receiver, if it is less that 18" you'll need a ball mount with rise, however, if it's more than 18", you'll need a ball mount with drop.
For example, if you measured 20"... view full answer...
For the roof rack, I recommend using the Rhino Rack Roof Rack for Toyota 4Runner using parts # RRVA126B-2, # RRSX100. This rack will fit on the raised side rails of your 2021 4Runner and allow you to carry a cargo basket like the Rhino-Rack XTray Pro Cargo Basket and 2 Bike Carrier - Steel - 58-1/4" x 41" - 165 lbs # RRRMCB03 which comes with axle mounts for 2 bikes, so it's going to be able to serve multiple purposes.
If you wanted to be able to carry surf boards on your roof rack you'd... view full answer...
The correct harnesses to wire the RedArc Tow Pro Elite # RED44FR on your 2006 Toyota 4Runner is the Tekonsha Custom Wiring Adapter for Trailer Brake Controllers - Pigtail - Toyota # 3040-P along with # 331-TPH-017. view full answer...
In order for the Rhino-Rack Batwing to fit crossbars they will need to have top channels for the T-Brackets. Since the factory roof rails on your 2020 Toyota 4Runner don't have that top slot you'll need to go with an aftermarket system instead.
I recommend going with the Rhino-Rack Vortex roof rack system, parts # RRVA126B-2 and # RRSX100, but if you are wanting a cost-effective roof rack then it's hard to beat the Malone AirFlow2 # MPG216.
Both systems have the top T-Slot channel so... view full answer...
While the # L68149 most likely corresponds to the inner bearing number of your hubs. If this is the case, you have either a 3.5k or a 4.4k axle.
In order to know absolutely sure, you need to know the corresponding outer bearing number or the inner and outer diameter of the grease seal. You most likely need to wipe away the grease in order to reveal the outer bearing number. In order to accomplish this, I recommend using calipers like the 4" Carbon Fiber Digital Caliper # PTW80157.
I... view full answer...
The information I have shows that the Tow Ready Replacement 7-Way Flat Pin and 4-flat Combo Adapter Harness, item # 20137, is the correct 7-way and 4-way replacement for the 2006 Toyota 4Runner, that is equipped with the factory 7-Way connector.
You will be able to use the 7-way and 4-way at the same time as long as your backup camera and your backup alarm do not require more amperage than the vehicle circuits can handle. If the backup camera is connected to the tail light circuit in the... view full answer...
In order to flat tow your 2016 Toyota 4Runner, you will need a base plate kit, tow bar, safety cable set, lighting solution, and a supplemental braking system. A supplemental braking system is indeed required by law in most states and many RV manufacturers will actually only honor your warranty if a braking system is in place when towing.
Starting with the base plate kit, the Roadmaster XL Base Plate Kit # 1185-1 that you referenced is a great choice and is confirmed to fit your 4Runner... view full answer...
The black rubber keel roller that are 10-inches and what we currently offer is # YR10000. Unfortunately, it's for a 5/8 inch shaft.
What you could do is replace the roller assembly with the # CE10404G. This V keel roller supports your boat's keel as it sits on the trailer.
I also included a link to all the keel rollers we currently offer for you to view. view full answer...
If the plug that you have found is functional, you may be able to use adapter # 3040-P. You will need to test the connector with a circuit tester like # 3808 if needed to determine the functions of the plug. I have included a link to the instructions which has a diagram that should help.
If you determine the plug will not fit, you will need to hardwire in a controller. First, you will need to have a 4-Way trailer connector installed if you do not already have one using # 118341. Then you... view full answer...
The correct brake controller wiring harness to connect the Tekonsha # TK63VR brake controller to your 2016 Toyota 4Runner is # 3041-P. view full answer...
When it comes to the pigtail for The Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional # 90885 there are 4 main wires that are needed to function properly there are as followed:
Black - 12 Volt Hot Lead
Red = Reverse Lights
Blue - Electric Brakes
White - Ground
The Blue and White wires are larger gauge because more power is needed to go through and is constantly being used. The wire connection area should be left of the steering column in your 2002 Toyota... view full answer...
To allow you to switch between your two vehicles you'll really just need two parts to be able to freely swap your Tekonsha P3 # 90195. You can use the Replacement Mounting Bracket for Tekonsha Voyager Brake Controller # 2178, which also works with the P3, to mount the controller. Then, you can use the plug and play adapter harness # 3041-P to easily install the your Prodigy P3 in your 2021 4Runner.
I've linked a short installation video of a P3 on a 4Runner that you can use as a guide. view full answer...
Since your 1997 Toyota 4 Runner isn't prewired for a brake controller, you'll need to hardwire the Tekonsha P3, part # 90195. Since your vehicle already has a 4 pole, the only other item you'll need to complete the installation is our Brake Controller Installation Kit, part # ETBC7. The kit includes the # 37185 adapter you'd looked at, as well as all the wire, hardware and circuit breakers needed to complete the installation.
I've linked to some demonstration videos and a help article... view full answer...
Your towing capacity will depend on how the vehicle is equipped. According to my research, the V6 4 Runner model can tow up to 5000 lbs. The V8 models have a higher tow rating, 7300 lb for 2WD models, or 7000 lb for 4WD models. I would strongly suggest consulting your owners manual or your Toyota dealer for confirmation. Your owner's manual should state if your vehicle is rated for weight distribution.
You'd also need to check your hitch, to ensure it's rated for weight distribution.... view full answer...
It sounds like K-Source Panoramic Aspheric Rearview Mirror - 13" # KSRM1300 would work for you on your 1997 4Runner. These are clip on mirrors designed to provide you with a panoramic view of what's going on behind you and would be my recommendation for this situation. view full answer...
Yes, we have exactly what you're needing!
In order to install the Redarc Tow-Pro Liberty Brake Controller # RED24FR control knob into the panel system on the left-hand side of your 2023 Toyota 4Runner steering wheel you just need the Mounting Panel # 331-TPSI-002. Be sure to also pick up the Plug and Play Wiring Harness # RED49FR to make installing the wiring easier!
Attached is an installation video of this controller on a 2023 4Runner for your reference. view full answer...
Thank you for purchasing your Thule WingBar Evo roof rack, parts # TH711400 and # TH710401, and your Thule Hull-A-Port Kayak Carrier # TH834. To install the carrier on the roof rack you will need an additional component, Thule adapter part # THXADAPT11. This will let you complete the installation. view full answer...
This is correct; you won't be able to use the Thule Hullavator # TH898 on factory bars since they don't extend outside of the side rails, which is required to let the boat down off the roof. You would also need crossbars that are at least 60" long to fit 2 Hullavators on, since they require a minimum of 28.5".
To add a new roof rack system I recommend using the Thule Roof Rack system that uses parts # TH711500 (60" long) and # TH710401 (Evo Raised Side Rail Feet), which will allow you... view full answer...
You can install your Tekonsha Primus IQ brake controller # TK90160 in your 2017 Toyota 4Runner by using the wiring adapter part # 3041-P. view full answer...
Go To Results